- 您現在的位置：買賣IC網 > PDF目錄371189 > TZA3001U (NXP SEMICONDUCTORS) SDH/SONET STM4/OC12 laser drivers PDF資料下載
參數資料
| 型號： | TZA3001U |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 其它接口 |
| 英文描述： | SDH/SONET STM4/OC12 laser drivers |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, UUC40 |
| 封裝： | 2 X 2 X 0.38 MM, DIE-40 |
| 文件頁數： | 6/22頁 |
| 文件大小： | 517K |
| 代理商： | TZA3001U |
1999 Aug 24
6
Philips Semiconductors
Preliminary specification
SDH/SONET STM4/OC12 laser drivers
TZA3001AHL; TZA3001BHL;
TZA3001U
Fig.4 Pin configuration of TZA3001BHL.
handbook, full pagewidth
TZA3001BHL
MGK272
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
9
1
1
1
1
1
1
1
3
3
3
2
2
2
2
2
GND
MONIN
GND
TONE
TZERO
BGAP
VCC(G)
GND
G
V
G
L
G
B
G
L
GND
VCC(R)
DLOOPQ
ONE
VCC(R)
ZERO
DLOOP
GND
G
D
D
V
A
G
E
V
FUNCTIONAL DESCRIPTION
The TZA3001AHL, TZA3001BHL and TZA3001U laser
drivers accept a 622 Mbits/s STM4 Non-Return to Zero
(NRZ) input data stream and generate an output signal
with sufficient current to drive a solid state Fabry Perot
(FP) or Distributed FeedBack (DFB) laser. They also
contain dual loop control circuitry for stabilizing the true
laser optical power levels representing logic 1 and logic 0.
The input buffers present a high impedance to the data
stream on the differential inputs (pins DIN and DINQ).
The input signal can be at CML level of approximately
200 mV (p-p) below the supply voltage, or at PECL level
upto800 mV (p-p).Theinputscanbeconfiguredtoaccept
CML signals by connecting external 50
pull-up resistors
between pins DIN and DINQ to V
CC(R)
. If PECL
compatibility is required, the usual Thevenin termination
can be applied.
For ECL signals (negative and referenced to ground) the
inputs should be AC-coupled to the signal source.
If AC-coupling is applied, a constant input signal (either
low of high) will bring the device in an undefined state.
To avoid this, it is recommended to apply a slight offset to
the input stage. The applied offset must be higher than the
specified value in Chapter “Characteristics”, but much
lower than the applied input voltage swing.
The RF path is fully differential and contains a differential
preamplifier and a main amplifier. The main amplifier is
designed to handle large peak currents required at the
output laser driving stage and is insensitive to supply
voltage variations. The output signal from the main
amplifier drives a current switch which supplies a
guaranteed maximum modulation current of 60 mA at
pins LA and LAQ. Pin BIAS delivers a guaranteed
maximum DC bias current of up to 90 mA for adjusting the
optical laser output to a level above its light emitting
threshold.
Automatic laser control
A laser with a Monitor PhotoDiode (MPD) is required for
the laser control circuit (see Figs 6 and 7).
The MPD current is proportional to the laser emission and
is applied to pin MONIN. The MPD current range is from
100 to 1000
μ
A (p-p).Theinputbufferisoptimizedtocope
with MPD capacitances up to 50 pF. To prevent the input
buffer breaking into oscillation with a low MPD
capacitance, it is required to increase the capacitance to
the minimum value specified in Chapter “Characteristics”
by connecting an extra capacitor between pin MONIN and
V
CC(G)
.
相關PDF資料 |
PDF描述 |
|---|---|
| TZA3004 | SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3004HL | SDH/SONET data and clock recovery unit STM1/4 OC3/12 |
| X00602 | SENSITIVE GATE SCR |
| X00602MA | 0.8A SCRs |
| X00602MA1AA2 | 0.8A SCRs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TZA3004 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3004HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET data and clock recovery unit STM1/4 OC3/12 |
| TZA3005 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3005H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3011A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:30 Mbits/s up to 3.2 Gbits/s A-rate(TM) laser drivers |
發布緊急采購，3分鐘左右您將得到回復。