- 您現在的位置：買賣IC網 > PDF目錄385035 > TSOP4856SB1 (Vishay Intertechnology,Inc.) Photo Modules for PCM Remote Control Systems PDF資料下載
參數資料
| 型號： | TSOP4856SB1 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Photo Modules for PCM Remote Control Systems |
| 中文描述： | 圖片模塊PCM的遠程控制系統 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 2036K |
| 代理商： | TSOP4856SB1 |
TSOP48..ZC1
Vishay Telefunken
3 (7)
Rev. 3, 29-Mar-01
www.vishay.com
Document Number 82132
Suitable Data Format
The circuit of the TSOP48..ZC1 is designed in that way
that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fullfill the following condition:
Carrier frequency should be close to center
frequency of the bandpass (e.g. 38kHz).
Burst length should be 10 cycles/burst or longer.
After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is necessary.
For each burst which is longer than 1.8ms a
corresponding gap time is necessary at some time in
the data stream. This gap time should be at least 4
times longer than the burst.
Up to 800 short bursts per second can be received
continuously.
Some examples for suitable data format are:
NEC Code, Toshiba Micom Format, Sharp Code, RC5
Code, RC6 Code, R–2000 Code.
When a disturbance signal is applied to the
TSOP48..ZC1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.
Some examples for such disturbance signals which
are suppressed by the TSOP48..ZC1 are:
DC light (e.g. from tungsten bulb or sunlight)
frequency
Continuous signal at 38kHz or at any other
ballast with high or low modulation (see Figure A or
Figure B).
Signals from fluorescent lamps with electronic
0
5
10
15
20
time [ms]
Figure A: IR Signal from Fluorescent Lamp with low Modulation
0
5
10
15
20
time [s]
Figure B: IR Signal from Fluorescent Lamp with high Modulation
相關PDF資料 |
PDF描述 |
|---|---|
| TSOP4856SI1 | Photo Modules for PCM Remote Control Systems |
| TSOP4856ON1 | IR Receiver Modules for Remote Control Systems |
| TSOP4856QJ1 | Photo Modules for PCM Remote Control Systems |
| TSOP4856UH1 | Photo Modules for PCM Remote Control Systems |
| TSOP4856YA1 | Photo Modules for PCM Remote Control Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSOP48-DIP40-UCP PRO | 制造商:Batronix Elektronik 功能描述:ADAPTOR TSOP48-DIP40 制造商:BATRONIX 功能描述:ADAPTOR, TSOP48-DIP40 |
| TSOP4P38 | 功能描述:紅外接收機 IR SENSOR IC 38KHZ RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
| TSOP5038TR | 功能描述:紅外接收機 2.7-5.5V 38kHz RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
| TSOP5038TT | 功能描述:紅外接收機 IR SENSOR IC 38KHZ RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
| TSOP56 | 功能描述:MODULE SOCKET FOR EMP-30 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
發布緊急采購，3分鐘左右您將得到回復。