- 您現在的位置：買賣IC網 > PDF目錄385030 > TSOP2236VI1 (Vishay Intertechnology,Inc.) Photo Modules for PCM Remote Control Systems PDF資料下載
參數資料
| 型號： | TSOP2236VI1 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Photo Modules for PCM Remote Control Systems |
| 中文描述： | 圖片模塊PCM的遠程控制系統 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 229K |
| 代理商： | TSOP2236VI1 |
TSOP22..QJ1
Vishay Semiconductors
Document Number 82206
Rev. 1.1, 31-Jan-05
www.vishay.com
5
Suitable Data Format
The circuit of the TSOP22..QJ1 is designed in that
way that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpass filter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal and dis-
turbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fulfill the following conditions:
Carrier frequency should be close to center fre-
quency of the bandpass (e.g. 38 kHz).
Burst length should be 10 cycles/burst or longer.
After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is necessary.
For each burst which is longer than 1.0 ms a corre-
sponding gap time is necessary at some time in the
data stream. This gap time should be at least 4 times
longer than the burst.
Up to 800 short bursts per second can be received
continuously.
Some examples for suitable data format are: NEC
Code (repetitive pulse), NEC Code (repetitive data),
Toshiba Micom Format, Sharp Code, RC5 Code,
RC6 Code, R-2000 Code, Sony Code.
When a disturbance signal is applied to the
TSOP22..QJ1 it can still receive the data signal. How-
ever the sensitivity is reduced to that level that no
unexpected pulses will occur.
Some examples for such disturbance signals which
are suppressed by the TSOP22..QJ1 are:
DC light (e.g. from tungsten bulb or sunlight)
Continuous signal at 38 kHz or at any other fre-
quency
Signals from fluorescent lamps with electronic bal-
last with high or low modulation
( see Figure 13 or Figure 14 ).
Figure 13. IR Signal from Fluorescent Lamp with low Modulation
Figure 14. IR Signal from Fluorescent Lamp with high Modulation
0
5
10
15
20
Time ( ms )
16920
I
IR Signal from fluorescent
lamp with low modulation
0
5
10
15
20
Time ( ms )
16921
I
IR Signal from fluorescent
lamp with high modulation
相關PDF資料 |
PDF描述 |
|---|---|
| TSOP2237WE1 | Photo Modules for PCM Remote Control Systems |
| TSOP2238UH1 | RECTIFIER BRIDGE 25A 400V 300A-ifsm 1.1V-vf 5uA-ir GBPCW 100/TRAY |
| TSOP2238VI1 | RECTIFIER BRIDGE 4A 800V 150A-ifsm 1V-vf 5uA-ir GBU 20/TUBE |
| TSOP2238WE1 | Photo Modules for PCM Remote Control Systems |
| TSOP2238ZC1 | Photo Modules for PCM Remote Control Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSOP2237 | 功能描述:紅外接收機 2.7-5.5V 36.7kHz 45D RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
| TSOP2238 | 功能描述:紅外接收機 4.5-5.5V 38kHz RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
| TSOP2238QJ1 | 制造商:Vishay Semiconductors 功能描述:IR SENSOR 3V-5V 20MM HEIGHT - Rail/Tube |
| TSOP2238SB1 | 制造商:Vishay Semiconductors 功能描述:PH.MODULE 28LHZ T. VIEW-E3 |
| TSOP2238SS1BS12 | 功能描述:紅外接收機 4.5-5.5V 38kHz RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。