- 您現在的位置：買賣IC網 > PDF目錄385021 > TSOP1233RF1 (Vishay Intertechnology,Inc.) Photo Modules for PCM Remote Control Systems PDF資料下載
參數資料
| 型號： | TSOP1233RF1 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Photo Modules for PCM Remote Control Systems |
| 中文描述： | 圖片模塊PCM的遠程控制系統 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 2319K |
| 代理商： | TSOP1233RF1 |
TSOP12..GL1
Vishay Telefunken
3 (8)
Rev. 8, 30-Mar-01
www.vishay.com
Document Number 82014
Suitable Data Format
The circuit of the TSOP12..GL1 is designed in that
way that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fullfill the following condition:
Carrier frequency should be close to center
frequency of the bandpass (e.g. 38kHz).
Burst length should be 10 cycles/burst or longer.
After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is neccessary.
For each burst which is longer than 1.8ms a
corresponding gap time is necessary at some time in
the data stream. This gap time should be at least 4
times longer than the burst.
Up to 800 short bursts per second can be received
continuously.
Some examples for suitable data format are:
NEC Code (repetitive pulse), NEC Code (repetitive
data), Toshiba Micom Format, Sharp Code, RC5
Code, RC6 Code, R–2000 Code.
When a disturbance signal is applied to the
TSOP12..GL1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.
Some examples for such disturbance signals which
are suppressed by the TSOP12..GL1 are:
DC light (e.g. from tungsten bulb or sunlight)
frequency
Continuous signal at 38kHz or at any other
ballast with high or low modulation (see Figure A or
Figure B).
Signals from fluorescent lamps with electronic
0
5
10
15
20
time [ms]
Figure A: IR Signal from Fluorescent Lamp with low Modulation
0
5
10
15
20
time [s]
Figure B: IR Signal from Fluorescent Lamp with high Modulation
相關PDF資料 |
PDF描述 |
|---|---|
| TSOP1233SB1 | Photo Modules for PCM Remote Control Systems |
| TSOP1233TB1 | Photo Modules for PCM Remote Control Systems |
| TSOP1233XG1 | Photo Modules for PCM Remote Control Systems |
| TSOP1256GL1 | Photo Modules for PCM Remote Control Systems |
| TSOP1236KD1 | Photo Modules for PCM Remote Control Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSOP1233SA1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
| TSOP1233SB1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
| TSOP1233SM1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
| TSOP1233TB1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
| TSOP1233UU1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Photo Modules for PCM Remote Control Systems |
發布緊急采購，3分鐘左右您將得到回復。