參數資料
型號: TSB41AB2I
廠商: Texas Instruments, Inc.
英文描述: IEEE 1394a-2000 TWO-PORT CABLE TRANSCEVER/ARBITER
中文描述: 個IEEE 1394a - 2000雙端口電纜TRANSCEVER /仲裁者
文件頁數: 38/50頁
文件大?。?/td> 662K
代理商: TSB41AB2I
SLLS418G
JUNE 2000
REVISED JANUARY 2003
38
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
receive (continued)
The sequence of events for a normal packet reception is as follows:
1
a.
Receive operation initiated. The PHY indicates a receive operation by asserting receive on the CTL
lines. Normally, the interface is idle when receive is asserted. However, the receive operation may
interrupt a status transfer operation that is in progress so that the CTL lines may change from status
to receive without an intervening idle.
Data-on indication. The PHY may assert the data-on indication code on the D lines for one or more
cycles preceding the speed-code.
Speed code. The PHY indicates the speed of the received packet by asserting a speed code on the D
lines for one cycle immediately preceding packet data. The link decodes the speed code on the first
receive cycle for which the D lines are not the data-on code. If the speed code is invalid, or indicates
a speed higher that that which the link is capable of handling, the link should ignore the subsequent data.
Receive data. Following the data-on indication (if any) and the speed-code, the PHY asserts packet
data on the D lines with receive on the CTL lines for the remainder of the receive operation.
b.
c.
d.
e.
Receive operation terminated. The PHY terminates the receive operation by asserting idle on the CTL
lines. The PHY asserts at least one cycle of idle following a receive operation.
00
00
10
XX
(a)
(b)
(c)
FF (Data-On)
D0
D7
CTL0, CTL1
SYSCLK
00
01
Figure 19. Null Packet Reception Timing
The sequence of events for a null packet reception is as follows:
1
a.
Receive operation initiated. The PHY indicates a receive operation by asserting receive on the CTL
lines. Normally, the interface is idle when receive is asserted. However, the receive operation may
interrupt a status transfer operation that is in progress so that the CTL lines may change from status
to receive without an intervening idle.
b.
Data-on indication. The PHY asserts the data-on indication code on the D lines for one or more cycles.
c.
Receive operation terminated. The PHY terminates the receive operation by asserting idle on the CTL
lines. The PHY asserts at least one cycle of idle following a receive operation.
Table 20. Receive Speed Codes
D0
D7
00XX XXXX
0100 XXXX
0101 0000
1YYY YYYY
DATA RATE
S100
S200
S400
data-on indication
NOTE: X = Output as 0 by PHY, ignored by LLC.
Y = Output as 1 by PHY, ignored by LLC.
相關PDF資料
PDF描述
TSB41LV03AI IEEE 1394a THREE-PORT CABLE TRANSCEIVER/ARBITER
TSC692E 672-pin FineLine BGA
TSC695F IC,FPGA,57120-CELL,CMOS,BGA,1020PIN,PLASTIC
TSC695FL IC,FPGA,79040-CELL,CMOS,BGA,1020PIN,PLASTIC
TSL1301 102 x 1 Linear Sensor Array with Hold
相關代理商/技術參數
參數描述
TSB41AB2IPAP 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
TSB41AB2PAP 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
TSB41AB2PAP(PBF) 制造商:Texas Instruments 功能描述:
TSB41AB2PAPG4 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
TSB41AB2PAPR 功能描述:緩沖器和線路驅動器 Two-Port Cable Xcvr/Arbiter RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel