- 您現在的位置：買賣IC網 > PDF目錄385013 > TPS6734I (Texas Instruments, Inc.) FIXED 12-V 120-mA BOOST-CONVERTER SUPPLY PDF資料下載
參數資料
| 型號： | TPS6734I |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | FIXED 12-V 120-mA BOOST-CONVERTER SUPPLY |
| 中文描述： | 固定12伏120毫安升壓轉換器供電 |
| 文件頁數： | 12/19頁 |
| 文件大?。?/td> | 285K |
| 代理商： | TPS6734I |
TPS6734I
FIXED 12-V 120-mA BOOST-CONVERTER SUPPLY
SLVS127A – AUGUST 1995 – REVISED JANUARY 1999
12
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
soft-start capacitor
Soft-start timing is controlled by the value of the SS capacitor. Table 1 lists soft-start time intervals for selected
capacitor values and circuit conditions. If the circuit starts up with no load (e.g. in flash-memory programming
supplies), no soft start is needed. Omitting the soft-start capacitor provides a minimum output-voltage rise time
from the shutdown state, improving the output start-up time.
Table 1. Typical Soft-Start Times
SUPPLY
VOLTAGE (V)
SOFT-START TIME (ms) VERSUS CAPACITANCE
(μ
F)
0.047
0.1
NO. CAP
0.47
1.0
5
0.70
22
42
220
400
7
0.46
15
185
225
9
0.38
10
17
88
155
Soft-start times are
±
35%
printed-circuit layout
Printed-circuit-board (PCB) layout is critical to quiet operation. A ground plane is recommended. Special
attention should be given to minimizing the lengths of the switching loops. The first loop is formed by OUT, the
diode, the output capacitor, and GND, the length of which can be minimized by connecting the anode of the diode
close to OUT. The output capacitor should be connected directly between the diode cathode and GND with the
shortest possible path. The second loop is formed by OUT, the inductor, the input capacitor, and GND. This loop
is less critical than the first; however, the connection of OUT, the inductor and the anode of the diode must be
minimized. Bypass capacitors should be located as close to the device as possible to prevent instability and
noise pickup. If a large V
CC
-to-GND bypass capacitor cannot be placed adjacent to the IC pins, the pins should
be bypassed directly with a small ceramic capacitor (e.g., 0.1
μ
F). The recommended layout, shown in
Figures 14 through 17, can provide guidance for PCB configuration (the ground plane beneath the TPS6734
and the short loops should be noted).
Plastic plug-in-type proto boards, or any construction scheme that allows long leads and the possibility of noise
pickup, should not be used when assembling a breadboard or prototype application circuit implementing the
TPS6734.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS6735D | FIXED NEGATIVE 5-V 200-mA INVERTING DC/DC CONVERTER |
| TPS6735P | FIXED NEGATIVE 5-V 200-mA INVERTING DC/DC CONVERTER |
| TPS6755D | ADJUSTABLE INVERTING DC/DC CONVERTER |
| TPS6755P | ADJUSTABLE INVERTING DC/DC CONVERTER |
| TPS68625 | ULTRALOW-NOISE, HIGH PSRR, FAST RF 1.5 A LOW-DROPOUT LINEAR REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS6734ID | 功能描述:直流/直流開關調節器 120mA 12V RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS6734IDG4 | 功能描述:直流/直流開關調節器 120mA 12V RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS6734IDR | 功能描述:直流/直流開關調節器 120mA 12V RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS6734IDRG4 | 功能描述:直流/直流開關調節器 Fixed 12-V 120-MA Boost-Conv Supply RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS6734IP | 功能描述:直流/直流開關調節器 120mA 12V RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。