參數資料
型號： TPS65105RGE
廠商： Texas Instruments, Inc.
英文描述： TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND VCOM BUFFER
中文描述： 三路輸出液晶供應線性穩壓器和VCOM緩沖器
文件頁數： 15/25頁
文件大?。?/td> 816K
代理商： TPS65105RGE
www.ti.com
Converter Loop Design and Stability
Design Procedure Quick Steps
1. Select the feedback resistor divider to set the output voltage.
2. Select the feedforward capacitor to place a zero at 50 kHz.
3. Select the compensation capacitor on pin COMP. The smaller the value, the higher the low frequency gain.
4. Use a 50-k
potentiometer in series to C
and monitor V
during load transients. Fine tune the load
transient by adjusting the potentiometer. Select a resistor value that comes closest to the potentiometer
resistor value. This needs to be done at the highest V
in
and highest load current since the stability is most
critical at these conditions.
Setting the Output Voltage and Selecting the Feedforward Capacitor
Vout
1.146 V
1
R1
R2
R1
430 k
SW
SW
FB1
SUP
C2+
C2/MODE
D1
C8
6.8 pF
C4
22
μ
F
C2
0.22
μ
F
R2
56 k
V
O
1
Up to 10 V/150 mA
z
1
2
C8
R1
TPS65100
TPS65105
SLVS496B–SEPTEMBER 2003–REVISED MARCH 2004
The TPS65100/05 converter loop can be externally compensated and allows access to the internal
transconductance error amplifier output at the COMP pin. A small feedforward capacitor across the upper
feedback resistor divider speeds up the circuit as well. To test the converter stability and load transient
performance of the converter, a load step from 50 mA to 250 mA is applied, and the output voltage of the
converter is monitored. Applying load steps to the converter output is a good tool to judge the stability of such a
boost converter.
The output voltage is set by the external resistor divider and is calculated as:
Across the upper resistor a bypass capacitor is required to speed up the circuit during load transients as shown
in Figure 15.
Figure 15. Feedforward Capacitor
Together with R1 the bypass capacitor C8 sets a zero in the control loop at approximately 50 kHz:
A value closest to the calculated value should be used. Larger feedforward capacitor values reduce the load
regulation of the converter and cause load steps as shown in Figure 16.
15
相關PDF資料
PDF描述
TPS65111 Triple Chargepump for LTPS LCD
TPS65110RGE LTPS LCD BIAS POWER SUPPLY TRIPLE CHARGE PUMP
TPS65111RGE LTPS LCD BIAS POWER SUPPLY TRIPLE CHARGE PUMP
TPS65121RGT SINGLE-INDUCTOR QUADRUPLE-OUTPUT TFT LCD POWER SUPPLY
TPS65120RGT SINGLE-INDUCTOR QUADRUPLE-OUTPUT TFT LCD POWER SUPPLY
相關代理商/技術參數
參數描述
TPS65105RGER 功能描述:LCD 驅動器 LCD Supply with Vcom Buffer RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TPS65105RGERG4 功能描述:LCD 驅動器 LCD Supply with Vcom Buffer RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TPS65110RGE 功能描述:電荷泵 Triple Chargepump for LTPS LCD RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube
TPS65110RGEG3 功能描述:電荷泵 Triple Chargepump for LTPS LCD RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube
TPS65110RGER 功能描述:電荷泵 Triple Chargepump for LTPS LCD RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*