- 您現在的位置：買賣IC網 > PDF目錄385013 > TPS61100RGE (Texas Instruments, Inc.) DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER PDF資料下載
參數資料
| 型號： | TPS61100RGE |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER |
| 中文描述： | 雙輸出，單電池升壓變換器 |
| 文件頁數： | 6/28頁 |
| 文件大小： | 507K |
| 代理商： | TPS61100RGE |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
www.ti.com
POWER SAVE MODE
The SKIPEN pin can be used to select different operation modes. To enable power save, SKIPEN must be set
high. Power save mode is used to improve efficiency at light load. In power save mode the converter only
operates when the output voltage trips below a set threshold voltage. It ramps up the output voltage with one or
several pulses and goes again into power save mode once the output voltage exceeds the set threshold voltage.
This power save mode can be disabled by setting the SKIPEN to GND.
AUTO DISCHARGE
The auto discharge function is needed in applications where the supply voltage of a microcontroller,
microprocessor or memory has to be removed during shutdown in order to make sure that the system quickly
goes in a defined state. The auto discharge function is enabled when the ADEN is set high. It is disabled when
the ADEN is set to GND. When the auto discharge function is enabled, the output capacitor is discharged after
the device is programmed in the shutdown mode. The output capacitor is discharged by an integrated switch of
400
, hence the discharge time depends on the size of the output capacitor.
LOW BATTERY DETECTOR CIRCUIT—LBI/LBO
The low-battery detector circuit is typically used to supervise the battery voltage and to generate an error flag
when the battery voltage drops below a user-set threshold voltage. The function is active only when the device is
enabled. When the device is disabled, both LBO-pin are high-impedance. There are three programmed
thresholds, 400 mV, 450 mV, and 500 mV. The outputs on LBO1 and LBO2 are shown as follows:
LOW-EMI SWITCH
The device integrates a circuit that removes the ringing that typically appears on the SW-node when the
converter enters discontinuous current mode. In this case, the current through the inductor ramps to zero and the
rectifying PMOS switch is turned off to prevent a reverse current flowing from the output capacitors back to the
battery. Due to the remaining energy that is stored in parasitic components of the semiconductor and the
inductor, a ringing on the SW-pin is induced. The integrated antiringing switch clamps this voltage to VBAT and
therefore dampens ringing.
LDO
The built-in LDO can be used to generate a second output voltage derived from the dc/dc converter output, from
the battery, or from another power source like an ac adapter or a USB power rail. The LDOSENSE input must be
connected to LDOOUT at fixed output voltage versions.
TPS61100, TPS61103
TPS61106, TPS61107
SLVS411B–JUNE 2002–REVISED APRIL 2004
DETAILED DESCRIPTION (continued)
LBI INPUT
(mV)
0-400
400-450
450-500
500-VBAT
LBO1
LBO2
0
1
0
1
0
0
1
1
1 means that the output stays at high-impedance and 0 means that the output goes active low. If there is only
one LBO output needed, both outputs can be tied together. Then the switching threshold is at 500 mV at LBI.
The battery voltage, at which the detection circuit switches, can be programmed with a resistive divider
connected to the LBI-pin. The resistive divider scales down the battery voltage to a voltage level of 400 mV
(450 mV, 500 mV), which is then compared to the LBI threshold voltage. The LBI-pin has a built-in hysteresis of
10 mV. See the application section for more details about the programming of the LBI-threshold. If the
low-battery detection circuit is not used, the LBI-pin should be connected to GND (or to VBAT) and the LBO-pin
can be left unconnected. Do not let the LBI-pin float.
6
相關PDF資料 |
PDF描述 |
|---|---|
| TPS61103RGE | DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER |
| TPS61106RGE | DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER |
| TPS61120 | SYNCHRONOUS BOOST CONVERTER WITH 1.1A SWITCH AND INTEGRATED LDO |
| TPS612 | MOSFET, P, I-PAK; Transistor type:MOSFET; Current, Id cont:15A; Resistance, Rds on:0.024R; Case style:TO-251 (I-Pak); Case style, alternate:I-PAK; Current, Idm pulse:45A; Power, Pd:30W; Transistor polarity:P; Voltage, Vds max: RoHS Compliant: Yes |
| TPS62020DRC | 600 mA/1.25 MHz HIGH-EFFICIENCY STEP-DOWN CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61100RGER | 功能描述:直流/直流開關調節器 Adj Hi-Eff Boost Con RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS61100RGERG4 | 功能描述:直流/直流開關調節器 Adj Hi-Eff Boost Con RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS61103 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL-OUTPUT, SINGLE-CELL BOOST CONVERTER |
| TPS61103EVM-216 | 功能描述:電源管理IC開發工具 TPS61103-216 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS61103PW | 功能描述:直流/直流開關調節器 3.3V Hi-Eff Boost Cnvrtr w/120mA LDO RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。