- 您現在的位置：買賣IC網 > PDF目錄382679 > TPS61030RSA (Texas Instruments, Inc.) 96% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 4A SWITCH PDF資料下載
參數資料
| 型號： | TPS61030RSA |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 96% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 4A SWITCH |
| 中文描述： | 96％高效同步升壓轉換器和4A條開關 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 375K |
| 代理商： | TPS61030RSA |
www.ti.com
DETAILED DESCRIPTION
Controller Circuit
The controller circuit of the device is based on a fixed frequency multiple feedforward controller topology. Input
voltage, output voltage, and voltage drop on the NMOS switch are monitored and forwarded to the regulator. So
changes in the operating conditions of the converter directly affect the duty cycle and must not take the indirect
and slow way through the control loop and the error amplifier. The control loop, determined by the error amplifier,
only has to handle small signal errors. The input for it is the feedback voltage on the FB pin or, at fixed output
voltage versions, the voltage on the internal resistor divider. It is compared with the internal reference voltage to
generate an accurate and stable output voltage.
Synchronous Rectifier
The device integrates an N-channel and a P-channel MOSFET transistor to realize a synchronous rectifier.
Because the commonly used discrete Schottky rectifier is replaced with a low RDS(ON) PMOS switch, the power
conversion efficiency reaches 96%. To avoid ground shift due to the high currents in the NMOS switch, two
separate ground pins are used. The reference for all control functions is the GND pin. The source of the NMOS
switch is connected to PGND. Both grounds must be connected on the PCB at only one point close to the GND
pin. A special circuit is applied to disconnect the load from the input during shutdown of the converter. In
conventional synchronous rectifier circuits, the backgate diode of the high-side PMOS is forward biased in
shutdown and allows current flowing from the battery to the output. This device however uses a special circuit
which takes the cathode of the backgate diode of the high-side PMOS and disconnects it from the source when
the regulator is not enabled (EN = low).
Device Enable
The device is put into operation when EN is set high. It is put into a shutdown mode when EN is set to GND. In
shutdown mode, the regulator stops switching, all internal control circuitry including the low-battery comparator is
switched off, and the load is isolated from the input (as described in the Synchronous Rectifier Section). This
also means that the output voltage can drop below the input voltage during shutdown. During start-up of the
converter, the duty cycle and the peak current are limited in order to avoid high peak currents drawn from the
battery.
Undervoltage Lockout
Softstart
When the device enables the internal start-up cycle starts with the first step, the precharge phase. During
precharge, the rectifying switch is turned on until the output capacitor is charged to a value close to the input
voltage. The rectifying switch current is limited in that phase. This also limits the output current under short-circuit
conditions at the output. After charging the output capacitor to the input voltage the device starts switching. Until
the output voltage is reached, the boost switch current limit is set to 40% of its nominal value to avoid high peak
currents at the battery during startup. When the output voltage is reached, the regulator takes control and the
switch current limit is set back to 100%.
TPS61030
TPS61031, TPS61032
SLUS534D–SEPTEMBER 2002–REVISED APRIL 2004
The peak current of the NMOS switch is also sensed to limit the maximum current flowing through the switch and
the inductor. The typical peak current limit is set to 4000 mA. An internal temperature sensor prevents the device
from getting overheated in case of excessive power dissipation.
The benefit of this feature for the system design engineer is that the battery is not depleted during shutdown of
the converter. No additional components have to be added to the design to make sure that the battery is
disconnected from the output of the converter.
An undervoltage lockout function prevents device start-up if the supply voltage on VBAT is lower than
approximately 1.6 V. When in operation and the battery is being discharged, the device automatically enters the
shutdown mode if the voltage on VBAT drops below approximately 1.6 V. This undervoltage lockout function is
implemented in order to prevent the malfunctioning of the converter.
11
相關PDF資料 |
PDF描述 |
|---|---|
| TPS61031RSA | 96% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 4A SWITCH |
| TPS61040DBV | LOW POWER DC/DC BOOST CONVERTER IN SOT-23 PACKAGE |
| TPS61041DBV | LOW POWER DC/DC BOOST CONVERTER IN SOT-23 PACKAGE |
| TPS61070DDC | 90% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 600-mA SWITCH |
| TPS61071DDC | 90% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 600-mA SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61030RSAR | 功能描述:直流/直流開關調節器 1Adj 1-A 96% Eff Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS61030RSAR | 制造商:Texas Instruments 功能描述:IC BOOST CONVERTER ADJ 16-QFN |
| TPS61030RSAR | 制造商:Texas Instruments 功能描述:IC, SYNC BOOST CONVERTER, QFN-16 |
| TPS61030RSARG4 | 功能描述:直流/直流開關調節器 1Adj 1-A 96% Eff Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS61031 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:96% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 4A SWITCH |
發布緊急采購，3分鐘左右您將得到回復。