- 您現在的位置：買賣IC網 > PDF目錄382679 > TPS61001 (Texas Instruments, Inc.) Low Input Voltage Boost Converter with Fixed 1.5V Output PDF資料下載
參數資料
| 型號： | TPS61001 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Low Input Voltage Boost Converter with Fixed 1.5V Output |
| 中文描述： | 具有固定 1.5V 輸出的低輸入電壓升壓轉換器 |
| 文件頁數： | 15/22頁 |
| 文件大?。?/td> | 389K |
| 代理商： | TPS61001 |
TPS61000, TPS61001, TPS61002, TPS61003, TPS61004, TPS61005, TPS61006
SINGLE-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD
SLVS279A – MARCH 2000 – REVISED MAY 2000
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
programming the low battery comparator threshold voltage
The current through the resistive divider should be about 100 times greater than the current into the LBI pin.
The typical current into the LBI pin is 0.01
μ
A, the voltage across R2 is equal to the reference voltage that is
generated on chip, which has a value of 500 mV
±
15 mV. The recommended value for R2 is therefore in the
range of 500 k
. From that, the value of resistor R1 depending on the desired minimum battery voltage V
BAT
,
can be calculated using below equation:
R1
R2
VTRIP
VREF
1
500 k
VBAT
0.5 V
1
(2)
For example, if the low-battery detection circuit should flag an error condition on the LBO output pin at a battery
voltage of 1.0 V, a resistor in the range of 500 k
should be chosen for R1.
The output of the low battery comparator is a simple open-drain output that goes active low if the battery voltage
drops below the programmed threshold voltage on LBI. The output requires a pullup resistor with a
recommended value of 1M
, and should only be pulled up to the V
OUT
. If not used, the LBO pin can be left
floating.
inductor selection
The output filter of inductive switching regulators is a low pass filter of second order. It consists of an inductor and
a capacitor, often referred to as storage inductor and output capacitor.
To select an inductor, keep the possible peak inductor current below the current limit threshold of the power
switch in your chosen configuration. For example, the current limit threshold of the TPS61000’s switch is
1100 mA at an output voltage of 3.3 V. The highest peak current through the inductor and the switch depends on
the output load, the input (V
BAT
) and the output voltage (V
OUT
). Estimation of the maximum average inductor
current can be done using the following equation:
IL
IOUTx
VOUT
VBATx 0.8
(3)
For example, for an output current of 100 mA at 3.3 V, at least 515 mA current will flow through the inductor at a
minimum input voltage of 0.8 V.
The second parameter for choosing the inductor is the desired current ripple in the inductor. Normally it is advis-
able to work with a ripple of less than 20% of the average inductor current. A smaller ripple will reduce the mag-
netic hysteresis losses in the inductor as well as output voltage ripple and EMI. But in the same way, regulation
time at load changes will rise. In addition, a larger inductor will increase the total system costs.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS61001DGS | SINGLE-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD |
| TPS61002DGS | SINGLE-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD |
| TPS61032RSA | 96% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 4A SWITCH |
| TPS61030RSA | 96% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 4A SWITCH |
| TPS61031RSA | 96% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 4A SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61001DGS | 功能描述:開關變換器、穩壓器與控制器 1.5V 100mA Boost RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TPS61001DGSG4 | 功能描述:開關變換器、穩壓器與控制器 Lo-In Voltage Boost Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TPS61001DGSR | 功能描述:開關變換器、穩壓器與控制器 Lo-In Voltage Boost Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TPS61001DGSRG4 | 功能描述:開關變換器、穩壓器與控制器 Lo-In Voltage Boost Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| TPS61002 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SINGLE-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD |
發布緊急采購，3分鐘左右您將得到回復。