- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS54260DGQR (TEXAS INSTRUMENTS INC) SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 PDF資料下載
參數資料
| 型號： | TPS54260DGQR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | GREEN, PLASTIC, MSOP-10 |
| 文件頁數： | 22/49頁 |
| 文件大?。?/td> | 1808K |
| 代理商： | TPS54260DGQR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
IND
Vinmax
Vout
Lo min =
Io
K
Vinmax
sw
-
www.ti.com
SLVSA86A – MARCH 2010 – REVISED DECEMBER 2010
Figure 49. 3.3V Output TPS54260 Design Example.
Output Inductor Selection (LO)
To calculate the minimum value of the output inductor, use Equation 28.
KIND is a coefficient that represents the amount of inductor ripple current relative to the maximum output current.
The inductor ripple current will be filtered by the output capacitor. Therefore, choosing high inductor ripple
currents will impact the selection of the output capacitor since the output capacitor must have a ripple current
rating equal to or greater than the inductor ripple current. In general, the inductor ripple value is at the discretion
of the designer; however, the following guidelines may be used.
For designs using low ESR output capacitors such as ceramics, a value as high as KIND = 0.3 may be used.
When using higher ESR output capacitors, KIND = 0.2 yields better results. Since the inductor ripple current is
part of the PWM control system, the inductor ripple current should always be greater than 150 mA for
dependable operation. In a wide input voltage regulator, it is best to choose an inductor ripple current on the
larger side. This allows the inductor to still have a measurable ripple current with the input voltage at its
minimum.
For this design example, use KIND = 0.3 and the minimum inductor value is calculated to be 11 mH. For this
design, a nearest standard value was chosen: 10 mH. For the output filter inductor, it is important that the RMS
current and saturation current ratings not be exceeded. The RMS and peak inductor current can be found from
For this design, the RMS inductor current is 2.51 A and the peak inductor current is 2.913 A. The chosen
inductor is a Coilcraft MSS1038-103NLB . It has a saturation current rating of 4.52 A and an RMS current rating
of 4.05 A.
As the equation set demonstrates, lower ripple currents will reduce the output voltage ripple of the regulator but
will require a larger value of inductance. Selecting higher ripple currents will increase the output voltage ripple of
the regulator but allow for a lower inductance value.
The current flowing through the inductor is the inductor ripple current plus the output current. During power up,
faults or transient load conditions, the inductor current can increase above the calculated peak inductor current
level calculated above. In transient conditions, the inductor current can increase up to the switch current limit of
the device. For this reason, the most conservative approach is to specify an inductor with a saturation current
rating equal to or greater than the switch current limit rather than the peak inductor current.
(28)
Copyright 2010, Texas Instruments Incorporated
29
Product Folder Link(s): TPS54260
相關PDF資料 |
PDF描述 |
|---|---|
| TPS54260QDGQRQ1 | 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS5430MDDAREPG4 | 8.5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54310MPWPREP | 6 A SWITCHING REGULATOR, 775 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS54310PWPRG4 | 6 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS54320RHLR | SWITCHING REGULATOR, 1320 kHz SWITCHING FREQ-MAX, PQCC14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS54260DRCR | 功能描述:直流/直流開關轉換器 3.5V-60Vin,2.5A,2.5 MHz Step Down SWIFT RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS54260DRCT | 功能描述:直流/直流開關轉換器 3.5V-60Vin,2.5A,2.5 MHz Step Down SWIFT RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS54260EVM-597 | 功能描述:電源管理IC開發工具 2.5A,10.8-13.2Vin SWIFT Conv Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS54260MDGQTEP | 功能描述:IC REG BUCK ADJ 2.5A 10MOSP 制造商:texas instruments 系列:Eco-Mode? 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:3.5V 電壓 - 輸入（最大值）:60V 電壓 - 輸出（最小值/固定）:0.8V 電壓 - 輸出（最大值）:60V 電流 - 輸出:2.5A 頻率 - 開關:100kHz ~ 2.5MHz 同步整流器:無 工作溫度:-40°C ~ 150°C（TJ） 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商器件封裝:10-MSOP-PowerPad 標準包裝:1 |
| TPS54260MDRCTEP | 功能描述:IC REG BUCK ADJ 2.5A 10VSON 制造商:texas instruments 系列:Eco-Mode? 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:3.5V 電壓 - 輸入（最大值）:60V 電壓 - 輸出（最小值/固定）:0.8V 電壓 - 輸出（最大值）:60V 電流 - 輸出:2.5A 頻率 - 開關:100kHz ~ 2.5MHz 同步整流器:無 工作溫度:-40°C ~ 150°C（TJ） 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商器件封裝:10-VSON（3x3） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。