- 您現在的位置：買賣IC網 > PDF目錄382678 > TPS5210DWR Voltage-Mode SMPS Controller PDF資料下載
參數資料
| 型號： | TPS5210DWR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Voltage-Mode SMPS Controller |
| 中文描述： | 電壓模式開關電源控制器 |
| 文件頁數： | 5/29頁 |
| 文件大小： | 500K |
| 代理商： | TPS5210DWR |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A – SEPTEMBER 1998 – REVISED MAY 1999
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description (continued)
droop compensation
The droop compensation network reduces the load transient overshoot/undershoot on V
O
, relative to V
REF
. V
O
is programmed to a voltage greater than V
REF
by an external resistor divider from V
O
to VSENSE to reduce the
undershoot on V
O
during a low-to-high load transient. The overshoot during a high-to-low load transient is
reduced by subtracting the voltage on DROOP from V
REF
. The voltage on IOUT is divided with an external
resistor divider, and connected to DROOP.
inhibit
INHIBIT is a TTL-compatible digital input used to enable the controller. When INHIBIT is low, the output drivers
are low and the slowstart capacitor is discharged. When INHIBIT goes high, the short across the slowstart
capacitor is released and normal converter operation begins. When the system-logic supply is connected to
INHIBIT, it also controls power sequencing by locking out controller operation until the system-logic supply
exceeds the input threshold voltage of the inhibit circuit. The 12-V supply and the system logic supply (either
5 V or 3.3 V) must be above UVLO thresholds before the controller is allowed to start up. The start threshold
is 2.1 V and the hysteresis is 100 mV for the INHIBIT comparator.
V
CC
undervoltage lockout (UVLO)
The undervoltage lockout circuit disables the controller while the V
CC
supply is below the 10-V start threshold
during power up. When the controller is disabled, the output drivers will be low and the slowstart capacitor is
discharged. When V
CC
exceeds the start threshold, the short across the slowstart capacitor is released and
normal converter operation begins. There is a 2-V hysteresis in the undervoltage lockout circuit for noise
immunity.
slowstart
The slowstart circuit controls the rate at which V
O
powers up. A capacitor is connected between SLOWST and
ANAGND and is charged by an internal current source. The current source is proportional to the reference
voltage, so that the charging rate of C
slowst
is proportional to the reference voltage. By making the charging
current proportional to V
REF
, the power-up time for V
O
will be independent of V
REF
. Thus, C
SLOWST
can remain
the same value for all VID settings. The slowstart charging current is determined by the following equation:
I
slowstart
= I(V
REFB
) / 5 (amps)
Where I(V
REFB
) is the current flowing out of V
REFB
.
It is recommended that no additional loads be connected to V
REFB
, other than the resistor divider for setting the
hysteresis voltage. The maximum current that can be sourced by the V
REFB
circuit is 500
μ
A
.
The equation for
setting the slowstart time is:
t
SLOWST
= 5
×
C
SLOWST
×
R
VREFB
(seconds)
Where R
VREFB
is the total external resistance from V
REFB
to ANAGND.
power good
The power-good circuit monitors for an undervoltage condition on V
O
. If V
O
is 7% below V
REF
, then the PWRGD
pin is pulled low. PWRGD is an open-drain output.
overvoltage protection
The overvoltage protection (OVP) circuit monitors V
O
for an overvoltage condition. If V
O
is 15% above V
REF
,
then a fault latch is set and both output drivers are turned off. The latch will remain set until V
CC
goes below the
undervoltage lockout value. A 3-
μ
s deglitch timer is included for noise immunity. Refer to the
LODRV
section
for information on how to protect the microprocessor against overvoltages due to a shorted fault across the
high-side power FET.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| TPS5210PWPR | Voltage-Mode SMPS Controller |
| TPS5211PWPR | Analog IC |
| TPS524 | PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION |
| TPS5300DAP | Analog IC |
| TPS535G1 | PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS5210DWRG4 | 功能描述:DC/DC 開關控制器 Synch Buck Cntrlr Volume Control RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS5210EVM-116 | 功能描述:VRM EVALUATION MODULE RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| TPS5210EVM-119 | 功能描述:HIGH-PERFORMANCE SYNCHRONOUS BUC RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| TPS5210EVM-126 | 功能描述:EVAL MOD FOR TPS5210 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| TPS5210PWP | 功能描述:DC/DC 開關控制器 Synch Buck Cntrlr Class-AB Audio Amp RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。