- 您現在的位置：買賣IC網 > PDF目錄382678 > TPS5102IDBT Analog IC PDF資料下載
參數資料
| 型號： | TPS5102IDBT |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 17/31頁 |
| 文件大?。?/td> | 1083K |
| 代理商： | TPS5102IDBT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
TPS5102
DUAL, HIGH-EFFICIENCY CONTROLLER FOR NOTEBOOK PC POWER
SLVS239 - SEPTEMBER 1999
17
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
current protection
The current limit in TPS5102 on each channel is set using an internal current source and an external resistor
(R18 or R19). The sensed high side MOSFET drain-to-source voltage drop is compared to the set point, if the
voltage drop exceeds the limit, the internal oscillator is activated, and it continuously reset the current limit until
the over-current condition is removed. The equation below should be used for calculating the external resistor
value for current protection setpoint:
Rcl
Rds(on)
(Itrip
0.000015
Iind(p-p) 2)
In skip mode,
Rcl
Rds(on)
(Itrip
0.000005
Iind(p-p) 2)
Where Rcl is the external current limit resistor (R10 or R11); Rds(on) is the high side MOSFET (Q1 or Q3)
on-time resistance. Itrip is the required current limit; Iind(p-p) is the peak-to-peak output inductor current.
Example for voltage mode: Rds(on) = 10 m
, Itrip = 5 A, Iind = 2 A, so Rcl = 4 k
.
loop-gain compensation
Voltage mode control is used in this controller for the output voltage regulation. To achieve fast, stabilized
control, two parts are discussed in this section: the power stage small signal modeling and the compensation
circuit design.
For the buck converter, the small signal modeling circuit is shown below:
+
-
a
c
ia
ic
p
D
1
Vap
D
d
∧
Ic d
∧
+
VI
RL
L
ZL
C
R
RC
ZRC
VO
From this equivalent circuit, several control transfer functions can be derived: input-to-output, output
impedance, and control-to-output. Typically the control-to-output transfer function is used for the feedback
control design.
Assuming Rc and RL are much smaller than R, the simplified small signal control-to-output transfer function is:
Vod
Vo
∧
d
(1
sCRc)
1
s C
Rc
R
L
L
R
s
2
LC
Where C is the output capacitance; Rc is the equivalent serial resistance (ESR) in the output capacitor; L is the
output inductor; RL is the equivalent serial resistance (DCR) in the output inductor; R is the load resistance.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| TPS5103IDB | SMPS Controller |
| TPS5103IDBR | SMPS Controller |
| TPS5210DWR | Voltage-Mode SMPS Controller |
| TPS5210PWPR | Voltage-Mode SMPS Controller |
| TPS5211PWPR | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS5102IDBTG4 | 功能描述:DC/DC 開關控制器 Dual Output Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS5102IDBTR | 功能描述:DC/DC 開關控制器 Dual Output Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS5102IDBTRG4 | 功能描述:DC/DC 開關控制器 Dual Output Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS5103 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MULTIPLE MODE SYNCHRONOUS DC/DC CONTROLLER |
| TPS5103DB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:MULTIPLE MODE SYNCHRONOUS DC/DC CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。