參數資料
型號： TPS40074RHL
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 2 A SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PQCC20
封裝： PLASTIC, QFN-20
文件頁數： 15/37頁
文件大小： 448K
代理商： TPS40074RHL
www.ti.com
3. COMPONENT SELECTION
L +
VO
VIN(max)
VIN(max) * VO
fSW DI
(17)
ILOAD_RMS + ILOAD
2 ) DI
2
12 +
15.03 A
(18)
IPK + ILOAD ) DI
2
2 +
16.65 A
(19)
CO u
L
ISTEP
2
VUNDER DMAX
VIN * VO
(20)
CO u
L
ISTEP
2
VOVER VO
(21)
ESR t
VRIPPLE
DI
(22)
TPS40074
SLUS617–APRIL 2005
3. 1 Power Train Components
Designers familiar with the buck converter can skip to section 3.2 Component Selection for TPS40074.
3.1.1 Output Inductor, LO
The output inductor is one of the most important components to select. It stores the energy necessary to keep
the output regulated when the switch MOSFET is turned off. The value of the output inductor dictates the peak
and RMS currents in the converter. These currents are important when selecting other components. Equation 17
can be used to calculate a value for L.
I is the allowable ripple in the inductor. Selecting I also sets the output current when the converter goes into
discontinuous mode (DCM) operation. Since this converter utilizes MOSFETs for the rectifier, DCM is not a major
concern. Select I to be between 20% and 30% of maximum ILOAD. For this design, I of 3 A was selected. The
calculated L is 1.1 H. A standard inductor with value of 1.0 H was chosen. This increases I by about 10% to
3.3 A.
With this I value, calculate the RMS and peak current flowing in LO. Note this peak current is also seen by the
switching MOSFET and synchronous rectifier.
3.1.2 Output Capacitor, CO,ELCOand MLCC
Several parameters must be considered when selecting the output capacitor. The capacitance value should be
selected based on the output overshoot, VOVER, and undershoot, VUNDER, during a transient load, ISTEP,onthe
converter. The equivalent series resistance (ESR) is chosen to allow the converter meet the output ripple
specification, VRIPPLE. The voltage rating must be greater than the maximum output voltage. Other parameters to
consider are: equivalent series inductance which is important in fast transient load situations. Also size and
technology can be factors when choosing the output capacitor. In this design a large capacitance electrolytic type
capacitor, CO ELCO, is used to meet the overshoot and under shoot specifications. Its ESR is chosen to meet
the output ripple specification. While a smaller multiple layer ceramic capacitor, CO MLCC, is used to filter high
frequency noise.
The minimum required capacitance and maximum ESR can be calculated using the equations below.
Using Equation 20 through Equation 22, the capacitance for CO should be greater than 495 F and its ESR
should be less than 9.1m. The 1000 F/25 V capacitor from Rubycon's MBZ or Panasonic's series EEU-FL was
chosen. Its ESR is 19 m, so two in parallel are used. The slightly higher ESR is offset by the four times
increase in capacitance. A 2.2 F/16 V MLCC is also added in parallel to reduce high frequency noise.
22
相關PDF資料
PDF描述
TPS40075RHLR 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20
TPS40075RHLTG4 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20
TPS40077PWPR 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40077PWPRG4 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40077PWPG4 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
相關代理商/技術參數
參數描述
TPS40074RHLR 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40074RHLRG4 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40074RHLT 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40074RHLTG4 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40075 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5V TO 18V INPUT 10 PIN SYNCHRONOUS BUCK CONTROLLER WITH POWER GOOD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*