- 您現在的位置：買賣IC網 > PDF目錄225340 > TPS40001EVM-001 (Texas Instruments, Inc.) TPS40001 Evaluation Module(TPS40001評估板) PDF資料下載
參數資料
| 型號： | TPS40001EVM-001 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | TPS40001 Evaluation Module(TPS40001評估板) |
| 中文描述： | TPS40001評估模塊（TPS40001評估板） |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 318K |
| 代理商： | TPS40001EVM-001 |
SLUU131A – September 2002 – Revised February 2003
10
TPS40001 Based Converter Delivers 10-A Output
5
PowerPAD
Packaging
The TPS4000X family is available in the DGQ version of TI’s PowerPAD
t thermally enhanced package. In the
PowerPAD
t, a thermally conductive epoxy is utilized to attach the integrated circuit die to the leadframe die
pad, which is exposed on the bottom of the completed package. The leadframe die pad can be soldered to the
PCB using standard solder flow techniques when maximum heat dissipation is required. However, depending
on power dissipation requirements, the PowerPAD
t may not need to soldered to the PCB.
The thermally conductive epoxy bonding the circuit die to the leadframe die pad causes a high resistance from
the leadframe die pad to the device ground pin 5. When the PowerPad
t package is soldered to the PCB, the
leadframe die pad can be connected to ground (pin 5), but this is not required. The leadframe die pad should
not be connected to other potentials in the circuit.
The PowerPAD
t package helps to keep the junction temperature rise relatively low even with the power
dissipation inherent in the onboard MOSFET drivers. This power loss is proportional to switching frequency,
drive voltage, and the gate charge needed to enhance the N-channel MOSFETs. Effective heat removal allows
the use of ultra small packaging while maintaining high component reliability.
To effectively remove heat from the PowerPAD
t package, a thermal land should be provided directly
underneath the package. This thermal land usually has vias that help to spread heat to internal copper layers
and/or the opposite side of the PCB. The vias should not have thermal reliefs that are often used on ground
planes, because this reduces the copper area to transfer heat. Additionally, the vias should be small enough
so that the holes are effectively plugged when plated. This prevents the solder from wicking away from the
connection between the PCB surface and the bottom of the part. A typical footprint pattern is shown in Figure 2,
but does not include the additional copper plane which includes the vias above and below the device.
2.92mm
(0.115”)
0.5mm
(0.0197”)
0.28mm
(0.011”)
1.40mm
(0.055”)
Via Dia.
0.33mm
(0.013”)
Miminum
PowerPad ”X”
1.3mm
(0.050”)
Minimum
PowerPad ”Y”
1.7mm
(0.068”)
Figure 3. PowerPAD
t PCB Layout Guidelines
The Texas Instrument document, PowerPAD
t Thermally Enhanced Package Application Report (Texas
Instrument Literature Number SLMA002) should be consulted for more information on the PowerPAD
t
package. This report offers in-depth information on the package, assembly and rework techniques, and
illustrative examples of the thermal performance of the PowerPAD
t package.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40001 | Low Input Voltage Mode Synchronous Buck Controller |
| TPS40002 | "Low Input (2.25V-5.5V) 600 kHz Frequency |
| TPS40003EVM | TPS40003 Evaluation Module(TPS40003評估板) |
| TPS40003 | Low Input Voltage Mode Synchronous Buck Controller |
| TPS40004 | "Low Input (2.25V-5.5V) 300 kHz Frequency |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40002 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-INPUT VOLTAGE-MODE SYNCHRONOUS BUCK CONTROLLER |
| TPS40002DGQ | 功能描述:電壓模式 PWM 控制器 Lo Input 600kHz Freq Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| TPS40002DGQG4 | 功能描述:電壓模式 PWM 控制器 Lo Input 600kHz Freq Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| TPS40002DGQR | 功能描述:電壓模式 PWM 控制器 Lo Input 600kHz Freq Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| TPS40002DGQRG4 | 功能描述:電壓模式 PWM 控制器 Lo Input 600kHz Freq Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。