- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS2393APWRG4 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 PDF資料下載
參數資料
| 型號： | TPS2393APWRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| 封裝： | GREEN, PLASTIC, TSSOP-14 |
| 文件頁數： | 10/30頁 |
| 文件大?。?/td> | 665K |
| 代理商： | TPS2393APWRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
TPS2393A
SLUS610 JULY 2004
18
www.ti.com
APPLICATION INFORMATION
Setting the Sense Resistor Value
Due to the currentlimiting action of the internal LCA, the maximum allowable load current for an implementation
is easily programmed by selecting the appropriate sense resistor value. The LCA acts to limit the sense voltage
VI(ISENS) to its internal reference. Once the voltage at the IRAMP pin exceeds approximately 4 V, this limit is
the clamp voltage, VREF_K. Therefore, a maximum sense resistor value can be determined from equation (1).
R
SENSE v
33 mV
IMAX
where:
D RSENSE is the resistor value
D IMAX is the desired current limit
When setting the sense resistor value, it is important to consider two factors, the minimum current that may be
imposed by the TPS2393A, and the maximum load under normal operation of the module. For the first factor,
the specification minimum clamp value is used, as seen in equation (1). This method accounts for the tolerance
in the sourced current limit below the typical level expected (40 mV/RSENSE). (The clamp measurement includes
LCA input offset voltage; therefore, this offset does not have to be factored into the current limit again.) Second,
if the load current varies over a range of values under normal operating conditions, then the maximum load level
must be allowed for by the value of RSENSE. One example of this is when the load is a switching converter, or
brick, which draws higher input current, for a given power output, when the distribution bus is at the low end of
its operating range, with decreasing draw at higher supply voltages. To avoid current-limit operation under
normal loading, some margin should be designed in between this maximum anticipated load and the minimum
current limit level, or IMAX > ILOAD(max), for equation (1).
For example, using a 20-m
sense resistor for a nominal 1-A load application provides a minimum of 650 mA
of overhead for load variance/margin. Typical bulk capacitor charging current during turn-on is 2 A
(40 mV/20 m
).
Setting the Inrush Slew Rate
The TPS2393A enables user-programming of the maximum current slew rate during load start-up events. A
capacitor tied to the IRAMP pin (C1 in the typical application diagram) controls the di/dt rate. Once the sense
resistor value has been established, a value for ramp capacitor CIRAMP, in microfarads, can be determined from
equation (2).
C
IRAMP +
11
100
R
SENSE
di
dt MAX
where:
D RSENSE is the sense resistor value in
D (di/dt)MAX is the desired maximum slew rate in A/s
For example, if the desired slew rate for the typical application shown is 1500 mA/mS, the calculated value for
CIRAMP is about 3700 pF. Selecting the next larger standard value of 3900 pF (as shown in the diagram) provides
some margin for capacitor and sense resistor tolerances.
As described in the Detailed Description section of this datasheet, the TPS2393A initiates ramp capacitor
charging, and consequently, load current di/dt at a reduced rate. This reduced rate applies until the voltage on
the IRAMP pin is about 0.5 V. The maximum di/dt rate, as set by equation (2), is effective once the device has
switched to the 10-
A charging source.
(1)
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2421-1DDAR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2421-2DDAR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2459RHBR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| TPS2459RHB | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| TPS24701DGK | POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2393DBT | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2393DBTG4 | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2393DBTR | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2393DBTRG4 | 功能描述:熱插拔功率分布 -48V Hot Swap G179 Pwr Mgr Ind Temp RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2393EVM | 功能描述:電源管理IC開發工具 Simple -48V Hot Swap Contr EVM RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。