- 您現在的位置：買賣IC網 > PDF目錄385946 > TPS2330EVM-184 (Texas Instruments, Inc.) TPS2330 48-V Telecom Hot Swap Evaluation Module and Interface Card(48V遠程通信熱交換電源控制器TPS2330的評估板與接口卡) PDF資料下載
參數資料
| 型號： | TPS2330EVM-184 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | TPS2330 48-V Telecom Hot Swap Evaluation Module and Interface Card(48V遠程通信熱交換電源控制器TPS2330的評估板與接口卡) |
| 中文描述： | TPS2330 48 - V電信熱插拔評估模塊和接口卡（48V的遠程通信熱交換電源控制器TPS2330的評估板與接口卡） |
| 文件頁數： | 19/22頁 |
| 文件大?。?/td> | 759K |
| 代理商： | TPS2330EVM-184 |
5-1
Setup of the EVM
"
!
For proper operation of the EVM, one 48-V power supply, and a voltage meter
or an oscilloscope are required.
Refer to the setup diagram in Figure 5
–
1 and follow these steps for hot plug
testing:
1)
Verify that the power-supply voltage is set at 48 V. Make sure the supply
has the capability to provide the current loads need. Turn off the supply.
2)
Connect a meter or oscilloscope to monitor the voltages from Vout+ (pin 1
of J1) to Vout
–
(pin 2 of J1) on the SLVP184 board.
3)
Plug the supply into the interface card; connect the supply from IN1 to
ground. Then turn on the power supply. Check the voltage from VIN1 to
GND, which should be about 48 V.
4)
Plug the hot-swap board (SLVP184) into the interface board (SLVP155).
The key installed between pins 1 and 2 of the edge connector insures that
the board can only be inserted in the correct direction.
5)
Test points or headers are provided for oscilloscope probes and/or multi-
meters. Read the voltage from the multimeters connecting from Vout+ to
Vout
–
on SLVP184. The value of the meter should be about 48 V. Other-
wise, the board may have problems or the testing may not be correct.
6)
Unplug the SLVP184 board from the interface card.
More evaluations such as adding loads to the output rails, can be performed
by following procedures similar to those presented above.
Chapter 5
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2330EVM-185 | TPS2330/TPS2331,TPS5102 InfiniBand SM Bulk Power Evalutation Module and Interface Card( InfiniBand SM 降壓電源管理器件TPS2330/TPS2331, TPS5102的評估板與接口卡) |
| TPS2350EVM | TPS2350 -48V Hot Swap/Supply Selector Evaluation Module(’-48V熱交換/電源選擇器TPS2350的評估板) |
| TPS2370EVM | Power Over Ethernet Powered Device (PD) EVM(在支持以太網功率驅動裝置的電源熱插拔評估) |
| TPS2811(中文) | Dual High-Speed MOSFET Drivers, Noninverting(雙路高速反相MOSFET驅動器) |
| TPS2812(中文) | Dual High-Speed MOSFET Drivers, Inverting(雙路高速同相MOSFET驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2330EVM-185 | 功能描述:電源管理IC開發工具 Infiniband Bulk Pow Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2330ID | 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2330IDG4 | 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2330IDR | 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2330IDRG4 | 功能描述:熱插拔功率分布 3-13V Sngl w/Pwr Gd Rpt Act-Lo Enable RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。