參數資料
型號： TPS2311PWR
英文描述： Analog IC
中文描述： 模擬IC
文件頁數： 13/20頁
文件大?。?/td> 411K
代理商： TPS2311PWR
TPS2330, TPS2331
SINGLE HOT SWAP POWER CONTROLLER WITH
CIRCUIT BREAKER AND POWER-GOOD REPORTING
SLVS277A – MARCH 2000– REVISED APRIL 2000
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
typical application diagram
This diagram shows a typical dual hot-swap application. The pullup resistors at PWRGD and Fault should be
relatively large (e.g. 100 k
) to reduce power loss unless they are required to drive a large load.
VREG
0.1
μ
F
IN
ISET
RISET
ISENSE
RSENSE
GATE DISCH
VSENSE
RVSENSE_TOP
RVSENSE_BOTTOM
+
FAULT
PWRGD
FAULT
PWRGD
TIMER
ENABLE
DGND
AGND
VO
ENABLE
1
μ
F
～
10
μ
F
3 V
～
13 V IN
TPS2331
System
Board
Figure 18. Typical Hot-Swap Application
input capacitor
A 0.1-
μ
F ceramic capacitor in parallel with a 1-
μ
F ceramic capacitor should be placed on the input power
terminals near the connector on the hot-plug board to help stabilize the voltage rails on the cards. The
TPS2330/31 does not need to be mounted near the connector or these input capacitors. For applications with
more severe power environments, a 2.2-
μ
F or higher ceramic capacitor is recommended near the input
terminals of the hot-plug board. A bypass capacitor for IN should be placed close to the device.
output capacitor
A 0.1-
μ
F ceramic capacitor is recommended per load on the TPS2330/31; these capacitors should be placed
close to the external FETs and to TPS2330/31. A larger bulk capacitor on the load is also recommended. The
value of the bulk capacitor should be selected based on the power requirements and the transients generated
by the application.
external FET
To deliver power from the input sources to the loads, the controller needs an external N-channel MOSFET. A
few widely used MOSFETs are shown in Table 1. But many other MOSFETs on the market can also be used
with TPS23xx in hot-swap systems.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料
PDF描述
TPS2340A Dual Slot PCI and PCIX 1.0 Hot-Plug Power Controller
TPS2340APFP SMPS Controller
TPS2341 Dual-Slot PCI Hot-Plug Power Controller with I2C Interface
TPS2345 CompactPCI Hot Swap Power Manager Industrial Temp IC that meets the PICMG Standard
TPS2392 Full Featured -48V Hot Swap Power Manager. Industrial Temp.
相關代理商/技術參數
參數描述
TPS2320ID 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IDG4 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IDR 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IDRG4 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IPW 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*