參數資料
型號： TPS2205DF
廠商： Texas Instruments, Inc.
英文描述： DUAL-SLOT PC CARD POWER-INTERFACE SWITCH FOR PARALLEL PCMCIA CONTROLLERS
中文描述： 雙插槽PC卡電源接口開關并聯的PCMCIA控制器
文件頁數： 19/28頁
文件大?。?/td> 463K
代理商： TPS2205DF
TPS2205
DUAL-SLOT PC CARD POWER-INTERFACE SWITCH
FOR PARALLEL PCMCIA CONTROLLERS
SLVS128D OCTOBER 1995 – REVISED JUNE 1998
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
output ground switches
Several PCMCIA power-distribution switches on the market do not have an active-grounding FET switch. These
devices do not meet the PC Card specification requiring a discharge of V
CC
within 100 ms. PC Card resistance
can not be relied on to provide a discharge path for voltages stored on PC Card capacitance because of possible
high-impedance isolation by power-management schemes. A method commonly shown to alleviate this
problem is to add to the switch output an external 100-k
resistor in parallel with the PC Card. Considering that
this is the only discharge path to ground, a timing analysis shows that the RC time constant delays the required
discharge time to more than 2 seconds. The only way to ensure timing compatibility with PC Card standards
is to use a power-distribution switch that has an internal ground switch, like that of the TPS22xx family, or add
an external ground FET to each of the output lines with the control logic necessary to select it.
In summary, the TPS2205 is a complete single-chip dual-slot PC Card power interface. It meets all currently
defined PCMCIA specifications for power delivery in 5-V, 3.3-V, and mixed systems, and offers a serial control
interface. The TPS2205 offers functionality, power savings, overcurrent and thermal protection, and fault
reporting in one 30-pin SSOP surface-mount package, for maximum value added to new portable designs.
power supply considerations
The TPS2205 has multiple pins for each of its 3.3-V, 5-V, and 12-V power inputs and for the switched V
CC
outputs. Any individual pin can conduct the rated input or output current. Unless all pins are connected in
parallel, the series resistance is significantly higher than that specified, resulting in increased voltage drops and
lost power. Both 12-V inputs must be connected for proper V
pp
switching; it is recommended that all input and
output power pins be paralleled for optimum operation.
Although the TPS2205 is fairly immune to power input fluctuations and noise, it is generally considered good
design practice to bypass power supplies, typically with a 1-
μ
F electrolytic or tantalum capacitor paralleled by
a 0.047-
μ
F to 0.1-
μ
F ceramic capacitor. It is strongly recommended that the switched V
CC
and V
pp
outputs be
bypassed with a 0.1-
μ
F or larger capacitor; doing so improves the immunity of the TPS2205 to electrostatic
discharge (ESD). Care should be taken to minimize the inductance of PCB traces between the TPS2205 and
the load. High switching currents can produce large negative-voltage transients, which forward biases substrate
diodes, resulting in unpredictable performance. Similary, no pin should be taken below –0.3 V.
overcurrent and thermal protection
The TPS2205 uses sense FETs to check for overcurrent conditions in each of the V
CC
and V
pp
outputs. Unlike
sense resistors or polyfuses, these FETs do not add to the series resistance of the switch; therefore, voltage
and power losses are reduced. Overcurrent sensing is applied to each output separately. When an overcurrent
condition is detected, only the power output affected is limited; all other power outputs continue to function
normally. The OC indicator, normally a logic high, is a logic low when any overcurrent condition is detected,
providing for initiation of system diagnostics and/or sending a warning message to the user.
During power up, the TPS2205 controls the rise time of the V
CC
and V
pp
outputs and limits the current into a
faulty card or connector. If a short circuit is applied after power is established (e.g., hot insertion of a bad card),
current is initially limited only by the impedance between the short and the power supply. In extreme cases, as
much as 10 A to 15 A may flow into the short before the current limiting of the TPS2205 engages. If the V
CC
or V
pp
outputs are driven below ground, the TPS2205 may latch nondestructively in an off state. Cycling power
will reestablish normal operation.
Overcurrent limiting for the V
CC
outputs is designed to activate if powered up into a short in the range of
1 A to 2.2 A, typically at about 1.6 A. The V
pp
outputs limit from 120 mA to 400 mA, typically around 280 mA.
The protection circuitry acts by linearly limiting the current passing through the switch rather than initiating a full
shutdown of the supply. Shutdown occurs only during thermal limiting.
相關PDF資料
PDF描述
TPS2301PWR Analog IC
TPS2311PWR Analog IC
TPS2340A Dual Slot PCI and PCIX 1.0 Hot-Plug Power Controller
TPS2340APFP SMPS Controller
TPS2341 Dual-Slot PCI Hot-Plug Power Controller with I2C Interface
相關代理商/技術參數
參數描述
TPS2205IDAP 功能描述:熱插拔功率分布 1A Dual-Slot PC Card Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2205IDAP 制造商:Texas Instruments 功能描述:IC PCMCIA PWR I/F SW 32-TSSOP 制造商:Texas Instruments 功能描述:IC, PCMCIA PWR I/F SW 32-TSSOP
TPS2205IDAPG4 功能描述:熱插拔功率分布 1A Dual-Slot PC Card Pwr Sw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2205IDAPR 功能描述:熱插拔功率分布 1A Dual-Slot PC Card Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2205IDAPRG4 功能描述:熱插拔功率分布 1A Dual-Slot PC Card Power Switch RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*