- 您現在的位置：買賣IC網 > PDF目錄98278 > TPL0202-10RUCR (TEXAS INSTRUMENTS INC) DIGITAL POTENTIOMETER, PQCC14 PDF資料下載
參數資料
| 型號： | TPL0202-10RUCR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 數字電位計 |
| 英文描述： | DIGITAL POTENTIOMETER, PQCC14 |
| 封裝： | 2 X2 MM, PLASTIC, MO-288X2GFE, QFN-14 |
| 文件頁數： | 7/23頁 |
| 文件大?。?/td> | 673K |
| 代理商： | TPL0202-10RUCR |
SCLK
DIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
C1
C0
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
SCLK
DIN
1
2
3
4
5
6
7
8
C1
C0
A1
A0
A) 16-clock cycle Data Write Sequence
B) 8-clock cycle Data Move/Copy Sequence
CS
SLIS135A
– DECEMBER 2010 – REVISED JANUARY 2011
Write-Wiper Register (Command 00)
Data written to the write-wiper registers (C1, C0 = 00) controls the wiper positions. The 8 data bits (D7 to D0)
indicate the position of the wiper. If DIN = 0x00h, the wiper moves to the position closest to the L terminal. If
DIN=0xFFh, the wiper moves to the position closest to the H terminal. This command writes data to the volatile
RAM, leaving the NV registers unchanged. When the device powers up, the data stored in the NV registers
transfers to the volatile wiper register, moving the wiper to the stored position
Write-NV Register (Command 01)
This command (C1, C0 = 01) stores the position of the wipers to the NV registers for use at power-up.
Alternatively, the
“copy wiper register to NV register” command can be used to store the position of the wipers to
the NV registers. Writing to the NV registers does not affect the position of the wipers.
Copy Wiper Register to NV Register (Command 10)
This command (C1, C0 = 10) stores the current position of the wiper to the NV register, for use at power-up. This
command may affect one potentiometer at a time, or both simultaneously, depending on the state of A1 and A0.
Alternatively, the
“write NV register” command can be used to store the current position of the wiper to the NV
register.
Copy NV Register to Wiper Register (Command 11)
This command (C1, C0 = 11) restores the wiper position to the previously stored position in the NV register. This
command may affect one potentiometer at a time, or both simultaneously, depending on the state of A1 and A0.
Figure 2. Digital Interface Write Sequence
Copyright
2010–2011, Texas Instruments Incorporated
15
Product Folder Link(s): TPL0202
相關PDF資料 |
PDF描述 |
|---|---|
| TPL8002-25PWR | DIGITAL POTENTIOMETER, PDSO16 |
| TPL9202PWPG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPL9202PWP | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPL9202PWPR | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2001CDGNR | SPECIALTY ANALOG CIRCUIT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPL0401A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:128 TAPS Single Channel Digital Potentiometer with I2C Interface |
| TPL0401A-10DCKR | 功能描述:數字電位計 IC 128 TAPS DIGITAL POT RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| TPL0401A-10QDCKRQ1 | 功能描述:DIGITAL POTENTIOMETER 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 圓錐:線性 配置:電位計，變阻器 電路數:1 抽頭數:128 電阻（歐姆）:10k 接口:I2C 存儲器類型:易失 電壓 - 電源:2.7 V ~ 5.5 V 特性:- 容差:±20% 溫度系數（典型值）:22 ppm/°C 電阻 -?游標（歐姆）（典型值）:35 工作溫度:-40°C ~ 125°C 封裝/外殼:6-TSSOP，SC-88，SOT-363 供應商器件封裝:SC-70-6 標準包裝:1 |
| TPL0401ADCK | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Works with low cost MSP430 based LaunchPad platform |
| TPL0401B | 制造商:TI 制造商全稱:Texas Instruments 功能描述:128 TAPS Single Channel Digital Potentiometer with I2C Interface |
發布緊急采購，3分鐘左右您將得到回復。