- 您現在的位置：買賣IC網 > PDF目錄98278 > TPIC8101DW (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PDSO20 PDF資料下載
參數資料
| 型號： | TPIC8101DW |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 封裝： | PLASTIC, SOIC-20 |
| 文件頁數： | 22/23頁 |
| 文件大?。?/td> | 511K |
| 代理商： | TPIC8101DW |
TPIC8101
KNOCK SENSOR INTERFACE
SLIS110A APRIL 2003 REVISED MAY 2005
8
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
function principle
The TPIC8101 is designed for knock sensor signal conditioning in automotive applications. The device is an
analog interface between the engine acoustical sensors or accelerometers and the fuel management systems
of a gasoline engine. The two wide-band amplifiers process signals from the piezoelectric sensors. Outputs of
the amplifiers feed a channel select mux switch and then a 3rd order antialiasing filter. This signal is converted
using an analog-to-digital conversion (10 bits with a sampling frequency of 200 kHz) prior to the gain stage.
The gain stage is adjustable via the SPI to compensate for the knock energies. The gain setting is selectable
up to 64 values ranging from 0.111 to 2.0.
The output of the gain stage feeds a band-pass filter circuit to process the particular frequency component
associated with the engine and transducer.
The band-pass filter has a gain of two and a center frequency range between 1.22 kHz and 19.98 kHz (64-bit
selection). The output from this stage is internally clamped.
The output from the band-pass filter is full-wave rectified with its output clamped below VDD.
The full-wave rectified signals are integrated using an integrator time constant set by the SPI and integration
time window set by the pulse width of INT/HOLD. At the start of each knock window, the integrator output is reset.
The output of the integrator is internally clamped and the digital output may be directly interfaced to the
microprocessor.
The integrated signal is converted to an analog format by a 10-bit DAC. The microprocessor may interface to
this signal, reads this data, and adjusts the spark ignition timing to optimize fuel efficiency related to load versus
engine RPM.
description of the functional terminals
supply voltage (VDD)
The VDD terminal is the input supply for the IC, typically 5 V ±5% tolerant. A noise filter capacitor of 4.7 F (typ)
is required on this terminal to ensure stability of the internal circuits.
ground (GND)
The GND terminal is connected to the system ground rail.
reference supply (Vref)
The Vref is an internally generated supply reference voltage for biasing the amplifier inputs. The terminal is used
to decouple any noise in the system by placing an external capacitor of 22 nF (typ).
buffered integrator output (OUT)
The OUT terminal is the output of the integrated signal. This is an analog signal interfaced to the microprocessor
A/D channel for data acquisition. A capacitor of 2.2 nF is used to stabilize the signal output.
integration/hold mode selection (INT/HOLD)
The INT/HOLD is an input control signal from the microprocessor to select either to integrate the sensed signal
or to hold the data for acquisition. There is an internal pulldown on this terminal (default HOLD mode).
chip select for SPI (CS)
The CS terminal allows serial communication to the IC through the SPI from a master controller. The chip select
is active low with an internal pullup (default inactive).
相關PDF資料 |
PDF描述 |
|---|---|
| TPIC8101DWR | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| TPIC8101DWG4 | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| TPIC8101DWRG4 | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| TPIC8300IPWRQ1 | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| TPIC9201PWPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPIC8101DW | 制造商:Texas Instruments 功能描述:IC KNOCK SENSOR INTERFACE SOIC-20 制造商:Texas Instruments 功能描述:IC, KNOCK SENSOR INTERFACE, SOIC-20 制造商:Texas Instruments 功能描述:IC, KNOCK SENSOR INTERFACE, SOIC-20; Sensor Case Style:SOIC; No. of Pins:20; Supply Voltage Min:-0.3V; Supply Voltage Max:5.5V; Operating Temperature Min:-40C; Operating Temperature Max:125C; SVHC:No SVHC (19-Dec-2012); Base |
| TPIC8101DWG4 | 功能描述:接口 - 專用 KNOCK SENSOR INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TPIC8101DWR | 功能描述:接口 - 專用 Knock Sensor Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TPIC8101DWRG4 | 功能描述:接口 - 專用 KNOCK SENSOR INTERFACE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TPIC8101EVM | 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。