參數資料
型號: TPD4113KLB2
元件分類: 運動控制電子
英文描述: BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23
封裝: 1.27 MM PITCH, PLASTIC, HZIP-23
文件頁數: 2/24頁
文件大?。?/td> 374K
代理商: TPD4113KLB2
TPD4113K
2006-11-01
10
External Parts
Standard external parts are shown in the following table.
Part
Recommended Value
Purpose
Remarks
C1, C2, C3
25 V/2.2
μF
Bootstrap capacitor
(Note 1)
R1
0.62
Ω ± 1% (1 W)
Current detection
(Note 2)
C4
25 V/10 μF
VCC power supply stability
(Note 3)
C
25 V
/0.1μF
VCC for surge absorber
(Note 3)
C6
16 V/1
μF
VREG power supply stability
(Note 3)
C7
16 V/1000 pF
VREG for surge absorber
(Note 3)
R2
5.1 k
Ω
FG pin pull-up resistor
(Note 4)
Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. The capacitor is
biased by VCC and must be sufficiently derated for it.
Note 2: The following formula shows the detection current: IO = VR ÷ R1 (For VR = 0.5 V )
Do not exceed a detection current of 1 A when using this product.
Note 3: When using this product, some adjustment is required in accordance with the use environment. When
mounting, place as close to the base of this product leads as possible to improve the ripple and noise
elimination.
Note 4: The DIAG pin is open drain. Note that when the DIAG pin is connected to a power supply with a voltage
higher than or equal to the VCC, a protection circuit is triggered so that the current flows continuously. If the
DIAG pin is not used, connect to the GND.
Handling precautions
(1)
Please control the input signal in the state to which the VCC voltage is steady. Both of the order of
the VBB power supply and the VCC power supply are not cared about either.
Note that if the power supply is switched off as described above, this product may be destroyed if the
current regeneration route to the VBB power supply is blocked when the VBB line is disconnected by
a relay or similar while the motor is still running.
(2)
The RS pin connecting the current detection resistor is connected to a comparator in the IC and also
functions as a sensor pin for detecting over current. As a result, over voltage caused by a surge
voltage, for example, may destroy the circuit. Accordingly, be careful of handling the IC or of surge
voltage in its application environment.
相關PDF資料
PDF描述
TPD4120AK BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDIP26
TPF21RGRA0 PUSHBUTTON SWITCH, DPDT, MOMENTARY, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE
TPIC7218QPFPRQ1 SPECIALTY ANALOG CIRCUIT, PQFP80
TPL1183525-262J-261 1 ELEMENT, 2610 uH, GENERAL PURPOSE INDUCTOR, SMD
TPS3619-50MDGKREP 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
相關代理商/技術參數
參數描述
TPD4120AK 制造商:Toshiba America Electronic Components 功能描述:
TPD4120AK(Q) 制造商:Toshiba America Electronic Components 功能描述:SINGLE CHIP INVERTER B DC MOTOR
TPD4121K 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC
TPD4121K(Q) 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Device, 250V, 1A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TPD4122K 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC