- 您現在的位置：買賣IC網 > PDF目錄98277 > TPD4112KLBR BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23 PDF資料下載
參數資料
| 型號： | TPD4112KLBR |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23 |
| 封裝： | 1.27 MM PITCH, LEAD FREE, PLASTIC, HZIP-23 |
| 文件頁數： | 2/27頁 |
| 文件大小： | 391K |
| 代理商： | TPD4112KLBR |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
TPD4112K
2006-06-30
10
External Parts
Standard external parts are shown in the following table.
Part
Recommended Value
Purpose
Remarks
C1, C2, C3
25 V/2.2
μF
Bootstrap capacitor
(Note 1)
R1
0.62
Ω ± 1% (1 W)
Current detection
(Note 2)
C4
10 V/1000 pF
± 5%
PWM frequency setup
(Note 3)
R2
27 k
Ω ± 5%
PWM frequency setup
(Note 3)
C5
25 V/10
μF
Control power supply stability
(Note 4)
C6
10 V/0.1
μF
VREG power supply stability
(Note 4)
R3
5.1 k
Ω
FG pin pull-up resistor
(Note 5)
Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. Although the IC
can operate at above the VBS undervoltage level, it is however recommended that the capacitor voltage
be greater than or equal to 13.5 V to keep the power dissipation small. The capacitor is biased by VCC and
must be sufficiently derated accordingly.
Note 2: The following formula shows the detection current: IO = VR ÷ R1 (VR = 0.5 V typ.)
Do not exceed a detection current of 1 A when using the IC.
Note 3: With the combination of Cos and RREF shown in the table, the PWM frequency is around 20 kHz. The IC
intrinsic error factor is around 10%.
The PWM frequency is broadly expressed by the following formula. (In this case, the stray capacitance of
the printed circuit board needs to be considered.)
fPWM = 0.65 ÷ {Cos × (RREF + 4.25 kΩ)} [Hz]
RREF creates the reference current of the PWM triangular wave charge/discharge circuit. If RREF is set too
small it exceeds the current capacity of the IC internal circuits and the triangular wave distorts. Set RREF to
at least 9 k
Ω.
Note 4: When using the IC, some adjustment is required in accordance with the use environment. When mounting,
place as close to the base of the IC leads as possible to improve noise elimination.
Note 5: The FG pin is open drain. Note that when the FG pin is connected to a power supply with a voltage higher
than or equal to the VCC, a protection circuit is triggered so that the current flows continuously. If the FG pin
is not used, connect to the GND.
Note 6: If noise is detected on the Input signal pin, add a capacitor between inputs.
Note 7: A Hall device should use an indium antimony system.
Handling precautions
(1)
When switching the power supply to the circuit on/off, ensure that VS < VVSOFF (all IGBT outputs
off). At that time, either the VCC or the VBB can be turned on/off first. Note that if the power supply is
switched off as described above, the IC may be destroyed if the current regeneration route to the VBB
power supply is blocked when the VBB line is disconnected by a relay or similar while the motor is
still running.
(2)
The triangular wave oscillator circuit, with externally connected COS and RREF, charges and
discharges minute amounts of current. Therefore, subjecting the IC to noise when mounting it on the
board may distort the triangular wave or cause malfunction. To avoid this, attach external parts to
the base of the IC leads or isolate them from any tracks or wiring which carries large current.
(3)
The PWM of this IC is controlled by the on/off state of the high-side IGBT.
(4)
If a motor is locked where VBB voltage is low and duty is 100%, it may not be possible to reboot after
the load is released as a result of the high side being ON immediately prior to the motor being locked.
This is because, over time, the bootstrap voltage falls, the high-side voltage decrease protection
operates and the high-side output becomes OFF. In this case, since the level shift pulse necessary to
turn the high side ON cannot be generated, reboot is not possible. A level shift pulse is generated by
either the edge of a Hall sensor output or the edge of an internal PWM signal, but neither edge is
available due to the motor lock and duty 100% command. In order to reboot after a lock, the high-side
power voltage must return to a level 0.5V (typ.) higher than the voltage decrease protection level, and
a high-side input signal must be introduced. As a high-side input signal is created by the
aforementioned level shift pulse, it is possible to reboot by reducing PWM duty to less than 100% or
相關PDF資料 |
PDF描述 |
|---|---|
| TPD4112K | BRUSHLESS DC MOTOR CONTROLLER, PZFM23 |
| TPD4113AKLB2 | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PZFM23 |
| TPD4124AK | BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDIP26 |
| TPD4125AK | BRUSHLESS DC MOTOR CONTROLLER, 4 A, PDIP26 |
| TPD4131K | BRUSHLESS DC MOTOR CONTROLLER, PDIP26 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPD4113AK | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:High Voltage Monolithic Silicon Power IC |
| TPD4113AK(LB2,Q) | 制造商:Toshiba America Electronic Components 功能描述: |
| TPD4113AK_07 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:High Voltage Monolithic Silicon Power IC |
| TPD4113K | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:High Voltage Monolithic Silicon Power IC |
| TPD4113K_07 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:High Voltage Monolithic Silicon Power IC |
發布緊急采購，3分鐘左右您將得到回復。