參數資料
型號： TPA741DG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻／視頻放大
英文描述： 0.35 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
封裝： GREEN, PLASTIC, MS-012AA, SOIC-8
文件頁數： 4/27頁
文件大?。?/td> 760K
代理商： TPA741DG4
www.ti.com
RL
CC
VO(PP)
VDD
–3 dB
fc
BTL AMPLIFIER EFFICIENCY
VL(RMS)
VO
IDD
IDD(RMS)
TPA741
SLOS316C – JUNE 2000 – REVISED JUNE 2004
APPLICATION INFORMATION (continued)
Figure 24. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
× the output power of a SE
configuration. Internal dissipation versus output power is discussed further in the thermal considerations section.
Linear amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across the
output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc
voltage drop that varies inversely to output power. The second component is due to the sine-wave nature of the
output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD.
The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal
power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out being equal to the ratio of power from the power supply
to the power delivered to the load. To accurately calculate the RMS values of power in the load and in the
amplifier, the current and voltage waveform shapes must first be understood (see Figure 25).
Figure 25. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are
different between SE and BTL configurations. In an SE application, the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
12
相關PDF資料
PDF描述
TPA741DRG4 0.35 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
TPA741DGNRG4 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
TPA741DGNG4 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
TPA751GQS 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA24
TPD12S521DBTR SPECIALTY CONSUMER CIRCUIT, PDSO38
相關代理商/技術參數
參數描述
TPA741DGN 功能描述:音頻放大器 Mono Diff Input Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA741DGNG4 功能描述:音頻放大器 Mono Diff Input Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA741DGNR 功能描述:音頻放大器 Mono Diff Input Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA741DGNRG4 功能描述:音頻放大器 Mono Diff Input Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA741DR 功能描述:音頻放大器 Mono Diff Input Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*