- 您現在的位置：買賣IC網 > PDF目錄98273 > TPA3125D2N (TEXAS INSTRUMENTS INC) 36 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP20 PDF資料下載
參數資料
| 型號： | TPA3125D2N |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 36 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP20 |
| 封裝： | ROHS COMPLIANT, PLASTIC, DIP-20 |
| 文件頁數： | 8/26頁 |
| 文件大?。?/td> | 467K |
| 代理商： | TPA3125D2N |
LOUT /ROUT
L
filter
C
filter
LOUT
L
filter
C
filter
L
filter
C
filter
ROUT
Power-Supply Decoupling, CS
BSN and BSP Capacitors
VCLAMP Capacitor
BYPASS Capacitor Selection
SLOS611 – DECEMBER 2008 ........................................................................................................................................................................................... www.ti.com
Figure 27. BTL Filter Configuration
Figure 28. SE Filter Configuration
The TPA3125D2 is a high-performance CMOS audio amplifier that requires adequate power-supply decoupling
to ensure that the output total harmonic distortion (THD) is as low as possible. Power-supply decoupling also
prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is
achieved by using two capacitors of different types that target different types of noise on the power-supply leads.
For higher-frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR)
ceramic capacitor, typically 0.1
F to 1 F, placed as close as possible to the device PV
CC pin works best. For
filtering lower frequency noise signals, a larger aluminum electrolytic capacitor of 470
F or greater placed near
the audio power amplifier is recommended. The 470-
F capacitor also serves as local storage capacitor for
supplying current during large signal transients on the amplifier outputs. The PVCC terminals provide the power
to the output transistors, so a 470-
F or larger capacitor should be connect to each PVCC terminal. A 10-F
capacitor on the AVCC terminal is adequate. These capacitors must be properly derated for voltage and
ripple-current rating to ensure reliability.
The half H-bridge output stages use only NMOS transistors. Therefore, they require bootstrap capacitors for the
high side of each output to turn on correctly. A 220-nF ceramic capacitor, rated for at least 25 V, must be
connected from each output to its corresponding bootstrap input. Specifically, one 220-nF capacitor must be
connected from LOUT to BSL, and one 220-nF capacitor must be connected from ROUT to BSR.
The bootstrap capacitors connected between the BSx pins and their corresponding outputs function as a floating
power supply for the high-side N-channel power MOSFET gate-drive circuitry. During each high-side switching
cycle, the bootstrap capacitors hold the gate-to-source voltage high enough to keep the high-side MOSFETs
turned on.
To ensure that the maximum gate-to-source voltage for the NMOS output transistors is not exceeded, one
internal regulator clamps the gate voltage. One 1-
F capacitor must be connected from VCLAMP (pin 11) to
ground and must be rated for at least 16 V. The voltages at the VCLAMP terminal may vary with VCC and may
not be used for powering any other circuitry.
The scaled supply reference (VBYP) nominally provides an AVCC/8 internal bias for the preamplifier stages. The
external capacitor for this reference, CBYP, is a critical component and serves several important functions. During
start-up or recovery from shutdown mode, CBYP determines the rate at which the amplifier starts. The start up
time is proportional to 0.5 s per microfarad. Thus, the recommended 1-
F capacitor results in a start-up time of
approximately 500 ms. The second function is to reduce noise produced by the power supply caused by coupling
with the output drive signal. This noise could result in degraded power-supply rejection and THD+N.
16
Copyright 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA3125D2
相關PDF資料 |
PDF描述 |
|---|---|
| TPA3200D1DCP | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA3200D1DCPR | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA3200D1DCPRG4 | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA3200D1DCPG4 | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA321DGNR | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA3128D2DAP | 功能描述:IC AUDIO AMP CLASS D 32HTSSOP 制造商:texas instruments 系列:- 包裝:管件 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C（TA） 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬）裸露焊盤 標準包裝:46 |
| TPA3128D2DAPR | 功能描述:IC AUDIO AMP CLASS D 32-HTSSOP 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C（TA） 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬）裸露焊盤 標準包裝:1 |
| TPA3128D2EVM | 功能描述:TPA3128D2EVM 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| TPA3129D2DAP | 功能描述:IC AUDIO AMP CLASS D 32HTSSOP 制造商:texas instruments 系列:- 包裝:管件 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路和熱保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬） 標準包裝:46 |
| TPA3130D2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:15W,30W,50W Filter-Free Class-D Stereo Amplifier Family with AM Avoidance |
發布緊急采購，3分鐘左右您將得到回復。