參數資料
型號： TPA2028D1YZFT
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻／視頻放大
英文描述： 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
封裝： 1.63 X 1.63 MM, GREEN, DSBGA-9
文件頁數： 14/37頁
文件大?。?/td> 1812K
代理商： TPA2028D1YZFT
SLOS660A
– JANUARY 2010 – REVISED MARCH 2011
TPA2028D1 AGC AND START-UP OPERATION
The TPA2028D1 is controlled by the I2C interface. The correct start-up sequence is:
1. Apply the supply voltage to the PVDD pin.
2. Apply a voltage above VIH to the EN pin. The TPA2028D1 powers up the I
2C interface and the control logic.
I2C registers are reset to default value. By default, the device is in active mode (SWS = 0). After 5 ms the
amplifier will enable the class-D output stage and become fully operational.
CAUTION
Do not interrupt the start-up sequence after changing EN from VIL to VIH.
CAUTION
Do not interrupt the start-up sequence after changing SWS from 1 to 0.
AGC STARTUP CONDITION
The amplifier gain at start-up depends on the following conditions:
1. Start-up from hardware reset (EN from 0 to 1): The amplifier starts up immediately at default fixed gain. AGC
starts controlling gain once the input audio signal exceeds noise gate threshold.
2. Start-up from software shutdown (SWS from 1 to 0): The amplifier starts up immediately at the latest fixed
gain during software shutdown, regardless the attack/ release time. For example:
– Audio is playing at fixed gain 6dB
– Devices goes to software shutdown (SWS = 1)
– Set fixed gain from 6 dB to 12 dB
– Remove software shutdown (SWS = 0)
– Amplifier starts up immediately at 12 dB
3. During audio playback with AGC on, gain changes according to attack/ release time. For example:
– Audio is playing at fixed gain 6 dB and 1:1 compression ratio
– Set fixed gain from 6 dB to 12 dB, at release time 500 ms / 6 dB
– Amplifier will take 500 ms to ramp from 6 dB to 12 dB
4. When EN = 0 and SWS = 0, the amplifier is set at fixed gain. The amplifier starts up at fixed gain when EN
transitions from 0 to 1.
The default conditions of TPA2028D1 allows audio playback without I2C control. Refer to Table 4 for entire
default conditions.
There are several options to disable the amplifier:
Write EN = 0 to the register (0x01, 6). This write disables the amplifier, but leaves all other circuits operating.
Write SWS = 1 to the register (0x01, 5). This action disables most of the amplifier functions.
Apply VIL to EN. This action shuts down all the circuits and has very low quiescent current consumption. This
action resets the register to its default values.
CAUTION
Do not interrupt the shutdown sequence after changing EN from VIH to VIL.
Do not interrupt the shutdown sequence after changing SWS from 0 to 1.
Copyright
2010–2011, Texas Instruments Incorporated
21
Product Folder Link(s): TPA2028D1
相關PDF資料
PDF描述
TPA2031D1YZFT 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA9
TPA2031D1YZF 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA9
TPA2031D1YZFR 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, BGA9
TPA2032D1YZFR 2.75 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9
TPA2032D1YZF 2.75 W, 1 CHANNEL, AUDIO AMPLIFIER, BGA9
相關代理商/技術參數
參數描述
TPA2028D1YZFT 制造商:Texas Instruments 功能描述:SPEAKER AMPLIFIER IC
TPA2029D1 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-W Mono Class-D Audio Amplifier With SmartGain? AGC/DRC
TPA2029D1YZFEVM 功能描述:音頻 IC 開發工具 TPA2029D1 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA2029D1YZFR 功能描述:音頻放大器 3W Mono Class-D Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA2029D1YZFT 功能描述:音頻放大器 3W Mono Class-D Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*