- 您現在的位置：買賣IC網 > PDF目錄385010 > TPA2010D1YEF (Texas Instruments, Inc.) 2.5-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | TPA2010D1YEF |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 2.5-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER |
| 中文描述： | 2.5單聲道無濾波器D類音頻功率放大器 |
| 文件頁數： | 16/23頁 |
| 文件大小： | 415K |
| 代理商： | TPA2010D1YEF |
SLOS417A OCTOBER 2003 REVISED DECEMBER 2003
www.ti.com
16
Component Location
Place all the external components very close to the TPA2010D1. The input resistors need to be very close to
the TPA2010D1 input pins so noise does not couple on the high impedance nodes between the input resistors
and the input amplifier of the TPA2010D1. Placing the decoupling capacitor, C
S
, close to the TPA2010D1 is
important for the efficiency of the class-D amplifier. Any resistance or inductance in the trace between the device
and the capacitor can cause a loss in efficiency.
Trace Width
Recommended trace width at the solder balls is 75
μ
m to 100
μ
m to prevent solder wicking onto wider PCB
traces. Figure 34 shows the layout of the TPA2010D1 evaluation module (EVM).
For high current pins (V
DD
, GND V
O+
, and V
O
) of the TPA2010D1, use 100-
μ
m trace widths at the solder balls
and at least 500-
μ
m PCB traces to ensure proper performance and output power for the device.
For input pins (IN, IN+, and SHUTDOWN) of the TPA2010D1, use 75-
μ
m to 100-
μ
m trace widths at the solder
balls. IN and IN+ pins need to run side-by-side to maximize common-mode noise cancellation. Placing input
resistors, R
IN
, as close to the TPA2010D1 as possible is recommended.
375 m
(+0, 25 m)
275 m
(+0, 25 m)
Circular Solder Mask Opening
Paste Mask (Stencil)
= Copper Pad Size
75 m
100 m
100 m
100 m
100 m
100 m
75 m
75 m
Figure 34. Close Up of TPA2010D1 Land Pattern From TPA2010D1 EVM
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2010D1YZF | 2.5-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER |
| TPA4411YZH | Filter Module with Resistor Network |
| TPA4411RTJ | 80-mW CAPLESS STEREO HEADPHONE DRIVER |
| TPA751GQS | 700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER WITH DIFFERENTIAL INPUTS |
| TPA751GQSR | Amplifier. Other |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2010D1YEFR | 功能描述:音頻放大器 Mono Filter-Free Class-D in WCSP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2010D1YEFT | 功能描述:音頻放大器 Mono Filter-Free Class-D in WCSP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2010D1YZF | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.5-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER |
| TPA2010D1YZFR | 功能描述:音頻放大器 Mono Filter-Free Class-D in WCSP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2010D1YZFRG4 | 制造商:TI 功能描述:AUDIO POWER AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。