參數資料
型號: TOP414
廠商: Power Integrations, Inc.
英文描述: Three-terminal DC to DC PWM Switch
中文描述: 三端直流到直流PWM開關
文件頁數: 6/16頁
文件大?。?/td> 434K
代理商: TOP414
TOP412/414
A
4/99
6
Figure 7. Schematic Diagram of a 5 V, 10 W Isolated DC to DC Converter.
PI-2220-120998
D2
MBRD620CT
9, 10
D3
1N4148
C3
330
μ
F
10 V
C5
330
μ
F
6.3 V
T1
D1
MURS120T3
VR1
ZGL41-100
U3
TL431ACD
R3
10k
C2
47
μ
F
U1
TOP414G
TOPSwitch
D
S
C
CONTROL
R1
15
L1
3.3
μ
H
C7
100 nF
U2
PC317A
R2
150
5 V
2.0 A
RTN
1
2
5
4
6, 7
36-72 V
DC Input
C1
10
μ
F
100 V
C4
330
μ
F
10 V
C9
2.2
μ
F
C6
330
μ
F
6.3 V
R4
10k
C8
100 nF
C
100 nF
General Circuit Operation
Figure 7 shows a typical DC-DC converter application using
the TOP414G. This supply delivers 5 V at 2 A and works over
a wide input range from 36-72 VDC. The power supply
operates at an ambient temperature of 0-50
°
C.
In order to achieve the highest possible efficiency and smallest
possible circuit board area, the primary and secondary current
waveform is shaped to have the lowest possible RMS and ripple
current. This is achieved by running very continuous and
utilizing the maximum duty cycle available.
For the example shown, the maximum component height is
12 mm. The EFD-20 transformer core was chosen to match this
maximum component height. The TOP414G has a high current
limit, which means that the EF20 core will saturate during
startup, until regulation is achieved. This is acceptable with the
TOP414G and does not cause device stress (provided the
maximum drain voltage is below 250 V peak and provided a
Zener is used for clamping). A Zener diode clamp circuit (VR1
and D1) is used in order to clamp the leakage inductance spike
to a fixed maximum voltage (an RCD, resistor capacitor diode,
clamp circuit would not be acceptable for this application).
In the example circuit, C1 provides local decoupling of the DC
input. This is required when the DC input source is distant from
this converter. A shottky diode (D2) with low voltage drop
provides secondary rectification and does not require additional
heat sinking (PC-board provides adequate heat sinking when
used with DPAK diode package). Tantalum capacitors (C3,C4)
provide low profile and small outline for secondary capacitance
(electrolytic capacitors can also be used as replacement).
Inductor L1 filters high frequency switching noise forming a
π
filter with the output capacitors (C3-C6). The control loop gain
is set by resistor R2 and the stability is influenced by R1, C3 ,C4,
C5 and C6. Resistors R3 and R4 set the DC regulation point and
shunt regulator U3 along with bypass capacitor C8, provide the
drive for the optocoupler U2. Any remaining switching noise
in the system is filtered by ceramic capacitor C9.
Capacitor C2 and resistor R1 form part of the CONTROL pin
feedback circuit. Capacitor C
is used solely to decouple high
frequency noise on the control pin.
相關PDF資料
PDF描述
TOP412G 0-21 W TOPSwitch using a 18-90 VDC input
TOP414G 0-21 W TOPSwitch using a 18-90 VDC input
TORX179P CONNECTOR ACCESSORY
TOS3104 7 SEGMENT LED DISPLAY
TOS5161 7 SEGMENT LED DISPLAY
相關代理商/技術參數
參數描述
TOP414G 功能描述:交流/直流開關轉換器 12 W 48 VDC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓(最大值):23.5 V 輸入/電源電壓(最小值):11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel
TOP414GN 功能描述:交流/直流開關轉換器 12 W 48 VDC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓(最大值):23.5 V 輸入/電源電壓(最小值):11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel
TOP414GN-TL 功能描述:交流/直流開關轉換器 12 W 48 VDC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓(最大值):23.5 V 輸入/電源電壓(最小值):11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel
TOP414G-TL 功能描述:交流/直流開關轉換器 12 W 48 VDC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓(最大值):23.5 V 輸入/電源電壓(最小值):11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel
TOP432DIP 制造商:Misc 功能描述: