參數資料
型號: TMS320F241FNQ
元件分類: 數字信號處理
英文描述: 16-Bit Digital Signal Processor
中文描述: 16位數字信號處理器
文件頁數: 29/116頁
文件大?。?/td> 1485K
代理商: TMS320F241FNQ
TMS320F243, TMS320F241
DSP CONTROLLERS
SPRS064B – DECEMBER 1997 – REVISED FEBRUARY 1999
29
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
interrupt request structure
1.
At the lower level of the hierarchy, the peripheral interrupt requests (PIRQs) from several peripherals to the
interrupt controller are ORed together to generate a request to the CPU. There is an interrupt flag bit and
an interrupt enable bit located in the peripheral for each event that can cause a peripheral interrupt request.
There is also one PIRQ for each event. If an interrupt-causing event occurs in a peripheral, and the
corresponding interrupt enable bit is set, the interrupt request from the peripheral to the interrupt controller
is asserted. This interrupt request simply reflects the status of the peripheral’s interrupt flag gated with the
interrupt enable bit. When the interrupt flag is cleared, the interrupt request is cleared. Some peripherals
have the capability to make either a high-priority or a low-priority interrupt request. If a peripheral has this
capability, the value of its interrupt priority bit is transmitted to the interrupt controller. The interrupt request
continues to be asserted until it is either automatically cleared by an interrupt acknowledge or cleared by
software.
2.
At the upper level of the hierarchy, the ORed PIRQs generate interrupt (INT) requests to the CPU. The
request to the ’24x CPU is a low-going pulse of 2 CPU clock cycles. The Peripheral Interrupt Expansion
(PIE) controller generates an INT pulse when any of the PIRQs controlling that INT go active. If any of the
PIRQs capable of asserting that CPU interrupt request are still active in the cycle following an interrupt
acknowledge for that INT, another INT pulse is generated (an interrupt acknowledge clears the
highest-priority pending PIRQ). Which CPU interrupt requests get asserted by which peripheral interrupt
requests, and the relative priority of each peripheral interrupt request, is defined in the interrupt controller
and is not part of any of the peripherals. This is shown in Table 10.
相關PDF資料
PDF描述
TMS320F241PGQ 16-Bit Digital Signal Processor
TMS320F243PGEQ 16-Bit Digital Signal Processor
TMS320F243PGES 16-Bit Digital Signal Processor
TMS320C3X 32-Bit Digital Signal Processor
TMS320C4X Digital Signal Processing Solutions
相關代理商/技術參數
參數描述
TMS320F241FNS 功能描述:數字信號處理器和控制器 - DSP, DSC 16B 5V fixed point DSP w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F241PG 功能描述:數字信號處理器和控制器 - DSP, DSC 16B 5V fixed point DSP w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F241PG 制造商:Texas Instruments 功能描述:IC C2000 DSP SMD 320F241 PQFP64
TMS320F241PGA 功能描述:數字信號處理器和控制器 - DSP, DSC 16B 5V fixed point DSP w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320F241PGS 功能描述:數字信號處理器和控制器 - DSP, DSC 16B 5V fixed point DSP w/ Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT