參數資料
型號： TMP86FH09NG
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDIP32
封裝： 0.400 INCH, 1.78 MM PITCH, LEAD FREE, PLASTIC, SDIP-32
文件頁數： 41/154頁
文件大小： 1433K
代理商： TMP86FH09NG
Page 125
TMP86CH09NG
12.3 Function
12.3.1 Software Start Mode
After setting ADCCR1<AMD> to “01” (software start mode), set ADCCR1<ADRS> to “1”. AD conver-
sion of the voltage at the analog input pin specified by ADCCR1<SAIN> is thereby started.
After completion of the AD conversion, the conversion result is stored in AD converted value registers
(ADCDR1, ADCDR2) and at the same time ADCDR2<EOCF> is set to 1, the AD conversion finished inter-
rupt (INTADC) is generated.
ADRS is automatically cleared after AD conversion has started. Do not set ADCCR1<ADRS> newly again
(Restart) during AD conversion. Before setting ADRS newly again, check ADCDR2<EOCF> to see that the
conversion is completed or wait until the interrupt signal (INTADC) is generated (e.g., interrupt handling rou-
tine).
Figure 12-2 Software Start Mode
12.3.2 Repeat Mode
AD conversion of the voltage at the analog input pin specified by ADCCR1<SAIN> is performed repeatedly.
In this mode, AD conversion is started by setting ADCCR1<ADRS> to “1” after setting ADCCR1<AMD> to
“11” (Repeat mode).
After completion of the AD conversion, the conversion result is stored in AD converted value registers
(ADCDR1, ADCDR2) and at the same time ADCDR2<EOCF> is set to 1, the AD conversion finished inter-
rupt (INTADC) is generated.
In repeat mode, each time one AD conversion is completed, the next AD conversion is started. To stop AD
conversion, set ADCCR1<AMD> to “00” (Disable mode) by writing 0s. The AD convert operation is stopped
immediately. The converted value at this time is not stored in the AD converted value register.
ADCDR1 status
EOCF cleared by reading
conversion result
Conversion result
read
ADCDR2<EOCF>
INTADC interrupt request
ADCDR2<ADBF>
ADCCR1<ADRS>
1st conversion result
2nd conversion result
Indeterminate
AD conversion start
ADCDR1
ADCDR2
Conversion result
read
Conversion result
read
Conversion result
read
相關PDF資料
PDF描述
TMP86FS49BUG 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
TMP86PS25F 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100
TMP87C800N 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
TMP89FH46LDUG 8-BIT, FLASH, MICROCONTROLLER, PQFP48
TMP89FM42UG 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
TMP86FH09NG(ZM) 功能描述:8位微控制器 -MCU TLCS870/C 16K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
TMP86FH12MG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 16KB FLASH 5V 30SSOP - Bulk 制造商:Toshiba America Electronic Components 功能描述:8BIT MCU 16K FLASH 512B RAM 86FH12
TMP86FH12MG(Z) 功能描述:8位微控制器 -MCU 16k Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
TMP86FH46ANG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 16KB FLASH 5V 42PIN SDIP - Bulk
TMP86FH46ANG(Z) 功能描述:8位微控制器 -MCU 16K Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*