- 您現在的位置：買賣IC網 > PDF目錄98265 > TMC222-PI20 STEPPER MOTOR CONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | TMC222-PI20 |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封裝： | SOIC-20 |
| 文件頁數： | 13/48頁 |
| 文件大?。?/td> | 457K |
| 代理商： | TMC222-PI20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
20
TMC222 DATASHEET (V. 1.12 / March 7, 2011)
Copyright 2004-2011 TRINAMIC Motion Control GmbH & Co. KG
5.2.2
Status Flags
The table below shows the flags which are accessable by the serial interface in order to receive
information about the internal status of the TMC222.
Flag
Mnemonic
Length
(bit)
Related
Command
Comment
Reset
state
Digital supply
Reset
VddReset
1
GetFullStatus1
Set to ‘1’ after power-up or after a micro-cut in the supply
voltage to warn that RAM contents may have been lost.
Is set to ‘0’ after GetFullStatus1 command.
‘1’
Over current in coil
A
OVC1
1
GetFullStatus1
Set to ‘1’ if an over current in coil #1 was detected. Is set to
‘0’ after GetFullStatus1 command.
‘0’
Over current in coil
B
OVC2
1
GetFullStatus1
Set to ‘1’ if an over current in coil #2 was detected. Is set to
‘0’ after GetFullStatus1 command.
‘0’
StepLoss
1
GetFullStatus1
Set to ‘1’ when under voltage, over current or over
temperature event was detected. Is set to ‘0’ after
GetFullStatus1 command. SetPosition and
GotoSecurePosition commands are ignored when
<StepLoss> = 1
‘0’
Secure position
enabled
SecEn
1
Internal use
‘0’ if SecPos = “100 0000 0000”
‘1’ otherwise
n.a.
Electrical Defect
ElDef
1
GetFullStatus1
Set to ‘1’ if open circuit or a short was detected, (<OVC1>
or <OVC2>). Is. Is set to ‘0’ after GetFullStatus1 command.
‘0’
Temperature Info
Tinfo
2
GetFullStatus1
Indicates the chip temperature
“00” = normal temperature
“01 = low temperature warning
“10” = high temperature warning
“11” = motor shutdown
“00”
Thermal Warning
TW
1
GetFullStatus1
Set to one if temperature raises above 145 °C. Is set to ‘0’
after GetFullStatus1 command.
‘0’
Thermal Shutdown
TSD
1
GetFullStatus1
Set to one if temperature raises above 155°C. Is set to ‘0’
after GetFullStatus1 command and Tinfo = “00”.
‘0’
Motion Status
Motion
3
GetFullStatus1
Indicates the actual behavior of the position controller.
“000”: Actual Position = Target Position; Velocity = 0
“001”: Positive Acceleration; Velocity > 0
“010”: Negative Acceleration; Velocity > 0
“011”: Acceleration = 0 Velocity = maximum pos Velocity
“100”: Actual Position /= Target Position; Velocity = 0
“101”: Positive Acceleration; Velocity < 0
“110”: Positive Acceleration; Velocity < 0
“111”: Acceleration = 0 Velocity = maximum neg Velocity
“000”
External Switch
Status
ESW
1
GetFullStatus1
Indicates the status of the external switch.
‘0’ = open
‘1’ = close
‘0’
Charge Pump
failure
CPFail
1
GetFullStatus1
‘0’ charge pump OK
‘1’ charge pump failure
‘0’
Electrical flag
HS
1
Internal use
<CPFail> or <UV2> or <ElDef>
‘0’
相關PDF資料 |
PDF描述 |
|---|---|
| TMC22290R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC22291R2C | COLOR SIGNAL ENCODER, PQCC44 |
| TMC2301G8A1 | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301G8A | SPECIALTY CONSUMER CIRCUIT, CPGA68 |
| TMC2301L1A1 | SPECIALTY CONSUMER CIRCUIT, CQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMC222-SI | 制造商:Trinamic 功能描述:MOTOR CNTRL I2C INTERFACE SOIC20 制造商:Trinamic 功能描述:MOTOR CNTRL, I2C INTERFACE, SOIC20 制造商:Trinamic 功能描述:IC MOTOR CTRL/DRVR, STEPPER, SOIC-20; Motor Type:Stepper; No. of Outputs:4; Output Current:800mA; Driver Case Style:SOIC; No. of Pins:20; Supply Voltage Min:8V; Supply Voltage Max:29V; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| TMC223-EVAL | 制造商:Trinamic 功能描述:EVAL MODULE FOR TMC223 |
| TMC223-LI | 制造商:Trinamic 功能描述: 制造商:Trinamic 功能描述:IC MOTOR CTRLR/DVR I2C 32QFN |
| TMC223-SI | 制造商:Trinamic 功能描述:Bulk |
| TMC2242 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。