參數資料
型號： TLE6266G
廠商： INFINEON TECHNOLOGIES AG
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PDSO28
封裝： 18 MM, PLASTIC, SOP-28
文件頁數： 49/50頁
文件大?。?/td> 1020K
代理商： TLE6266G
Datasheet TLE 6266 G
Version 2.21
8
July 29th, 2005
6
Circuit Description
The TLE 6266 G is a monolithic IC, which incorporates a failure tolerant low speed CAN-
transceiver for differential mode data transmission, a low dropout voltage regulator for
internal and external 5V supply as well as a SPI interface to control and monitor the IC.
Further there are three high side switches, two low side switches, a window watchdog
circuit and a reset circuit integrated. Figure 2 shows the block diagram of the TLE 6266.
6.1
Operation Modes
The TLE 6266 offers four different operation modes (see Figure 3), that are controlled
via the SPI input bits 9,10 (mode bits M0,M1) as shown in Table 1: the normal operation
mode, the receive-only mode, the Vbat stand-by mode and the cyclic wake operation
mode.
The cyclic wake mode itself is subdivided into two modes: the cyclic HS OFF and the
cyclic HS ON mode. Cyclic wake and Vbat stand-by mode are both designed for periods
that do not require communication on the CAN-Bus but offer a low power mode. The
lowest current consumption is achieved in the cyclic wake HS OFF mode.
Normal Operation Mode
The normal operation mode is designed to receive and transmit data messages as well
as to supply the ECU and control loads via HS- and LS- switches. RTL is switched to
VCC, RTH to GND. Table 3 gives an overview about the available functions in this mode.
RxD-only Mode
In the receive-only mode the receiver stage is activated and the transmitter stage is
deactivated. This means that data at the TxD input is not transmitted to the CAN bus but
receiving of data is still possible. The CANL line is pulled-up to VCC via the RTL output
and CANH is pulled to GND via RTH. Furthermore, it is possible to bypass the signal at
TxD to the RxD output during this mode.
This mode is useful in combination to a
dedicated network-management software that allows separate diagnosis for all nodes
(see Chapter 6.2). Table 3 gives an overview about the available functions in this mode.
Table 1
Operation modes bit settings
Mode Bit M1
(SPI Bit 10)
Mode Bit M0
(SPI Bit 9)
Normal operation 1
1
Cyclic Wake
1
0
RxD only
0
1
Vbat stand-by
0
相關PDF資料
PDF描述
TLE6280GP BRUSHLESS DC MOTOR CONTROLLER, PDSO36
TLE6361G SWITCHING REGULATOR, 425 kHz SWITCHING FREQ-MAX, PDSO36
TLE6363G DUAL SWITCHING CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO14
TLE6365G SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDSO8
TLE6387GV60 1 A SWITCHING CONTROLLER, 430 kHz SWITCHING FREQ-MAX, PDSO14
相關代理商/技術參數
參數描述
TLE6266GNT 制造商:Infineon Technologies AG 功能描述:CAN 125KBd Shutdown 5V Automotive 28-Pin DSO
TLE6270R 功能描述:基準電壓& 基準電流 POWERTRAIN RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
TLE6270RAUMA1 制造商:Infineon Technologies AG 功能描述:QUAD LOW SIDE INJECTOR DRIVER 制造商:Infineon Technologies AG 功能描述:ENGINECONTROL_IC - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC DRIVER INJECTOR QUAD DSO-36
TLE6280 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:3-Phase Bridge Driver IC
TLE6280GP 功能描述:馬達/運動/點火控制器和驅動器 GATE DRIVER ICS FOR EXTERNAL MOSFETS RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*