- 您現在的位置：買賣IC網 > PDF目錄383955 > TLE6262G (INFINEON TECHNOLOGIES AG) Fault Tolerant CAN - LDO PDF資料下載
參數資料
| 型號： | TLE6262G |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | Fault Tolerant CAN - LDO |
| 中文描述： | 容錯CAN -穩壓器 |
| 文件頁數： | 7/38頁 |
| 文件大?。?/td> | 809K |
| 代理商： | TLE6262G |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
Final Data
TLE 6262 G
7
version: 2.03 date: 2002-03-20
CAN Transceiver
The TLE 6262 is optimized for low speed data transmission up to 125 kbaud in
automotive applications. Normally a differential signal is transmitted or received
respectively. When a bus wiring failure (see
table 4
) is detected the device automatically
switches to a dedicated CANH or CANL single-wire mode to maintain the communication
if necessary. Therefore it is equipped with one differential receiver and four single ended
comparators (two for each bus line). To avoid false triggering by external RF influences
the single wire modes are activated after a certain delay time. As soon as the bus failure
disappears the transceiver switches back to differential mode after another time delay.
The bus failures are monitored via the diagnosis protocol of the SPI. Therefore it is
possible to distinguish 6 CAN bus failures or failure groups on the bits 8 to 13 (see
table
3
).
To reduce EMC caused by the transceiver the dynamic slopes of the CANL and CANH
signals are both limited and symmetric. This allows the use of an unshielded twisted or
parallel pair of wires for the bus. During single-wire transmission (bus-failure) the EMC
performance of the system is degraded from the differential mode.
The differential receiver threshold is set to typ. -2.8 V. This ensures correct reception in
the normal operation mode as well as in the failure cases 1, 2, 3a and 4 with a noise
margin as high as possible. When one of the bus failures 3, 5, 6, 6a, and 7 is detected,
the defective bus wire is disabled by switching off the affected bus termination and output
stage.
The CAN-transceiver offers three different operation modes that are controlled via the
SPI: the normal operation mode, Receive-only mode and V
bat
stand-by mode. Please
see the state diagram (
figure 3
). In the V
bat
stand-by mode the RTL output voltage is
switched to V
S
.
In case of a wake-up via the bus lines or one of the bus lines respectively, the TLE 6262
automatically sets the RxD output LOW. To send respectively receive messages the
CAN-transceiver can now be set in normal operation mode or receive-only mode by the
microcontroller.
When a reset occurs the transceiver circuit is automatically switched to V
bat
-stand-by
mode because the SPI input bits are automatically set LOW for this event.
A thermal shutdown of the CAN-transceiver circuit is monitored via the SPI diagnosis
bit 15.
相關PDF資料 |
PDF描述 |
|---|---|
| TLE6263 | LS CAN, LDO and HS Switch |
| TLE6263G | LS CAN, LDO and HS Switch |
| TLE6280 | 3-Phase Bridge Driver IC |
| TLE6280GP | 3-Phase Bridge Driver IC |
| TLE6285 | LIN-Transceiver LDO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE6263 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:LS CAN, LDO and HS Switch |
| TLE6263-3G | 功能描述:CAN 接口集成電路 BODY SYSTEM ICS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TLE62633GRBNT | 制造商:Infineon Technologies AG 功能描述:SBC'S |
| TLE62633GXUMA1 | 制造商:Infineon Technologies AG 功能描述:System Basic Chip T/R 制造商:Infineon Technologies AG 功能描述:BODY SYSTEM ICS - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC SYSTEM BASIS CHIP DSO-28 |
| TLE6263G | 功能描述:CAN 接口集成電路 BODY SYSTEM ICS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。