- 您現在的位置：買賣IC網 > PDF目錄384008 > TLE6230 (INFINEON TECHNOLOGIES AG) CABLE PDF資料下載
參數資料
| 型號： | TLE6230 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | CABLE |
| 中文描述： | 智能八路低端開關 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 746K |
| 代理商： | TLE6230 |
Data Sheet TLE 6230 GP
V2.1
Page
26. Aug. 2002
9
high level at this pin (within the data byte) will switch on the power switch, provided that the
corresponding parallel input is also switched on (AND-operation for channel 1 to 4).
SO
- Serial Output. Diagnostic data bits are shifted out serially at this pin, the most significant
bit first. SO is in a high impedance state until the
CS
pin goes to a logic low state. New diag-
nostic data will appear at the SO pin following the rising edge of SCLK.
RESET
- Reset pin. If the reset pin is in a logic low state, it clears the SPI shift register and
switches all outputs OFF. An internal pull-up structure is provided on chip.
Diagnostics
FAULT
- Fault pin. There is a general fault pin (open drain) which shows a high to low transi-
tion as soon as an error occurs for any one of the eight channels. This fault indication can be
used to generate a μC interrupt. Therefore a ‘diagnosis’ interrupt routine need only be called
after this fault indication. This saves processor time compared to a cyclic reading of the SO
information.
As soon as a fault occurs, the fault information is latched into the diagnosis register. A new
error will over-write the old error report. Serial data out pin (SO) is in a high impedance state
when
CS
is high. If
CS
receives a LOW signal, all diagnosis bits can be shifted out serially.
The rising edge of
CS
will reset all error registers.
There are two diagnostic bits per channel configured as shown in Figure 1.
Normal function:
The bit combination
HH
indicates that there is no fault condition, i.e. normal
function.
Overload, Short Circuit to Battery (SCB) or Overtemperature:
HL
is set when the current
limitation gets active, i.e. there is a overload, short to supply or overtemperature condition.
Open load:
An open load condition is detected when the drain voltage decreases below 3 V
(typ.).
LH
bit combination is set.
Short Circuit to GND:
If a drain to ground short circuit exists and the drain to ground current
exceeds 100 μA, short to ground is detected and the
LL
bit combination is set.
Diagnostic Serial Data Out SO
HH
HL
LH
LL
Normal function
Overload, Shorted Load or Overtemperature
Open Load
Shorted to Ground
Ch.8
Ch.7
Ch.6
Ch.5
15 14 13 12 11 10 9 8 - - - - -
Figure 1: Two bits per channel diagnostic feedback
相關PDF資料 |
PDF描述 |
|---|---|
| TLE6230GP | Smart Octal Low-Side Switch |
| TLE6232 | Smart Six Channel Low-Side Switch |
| TLE6232GP | Smart Six Channel Low-Side Switch |
| TLE6244 | 18 Channel Smart Lowside Switch |
| TLE6244X | 18 Channel Smart Lowside Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE6230GP | 功能描述:電源開關 IC - 配電 Smart Octal Low Side Switch RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TLE6230GP_09 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Smart Octal Low-Side Switch |
| TLE6230GPAUMA1 | 制造商:Infineon Technologies AG 功能描述:Power Switch Lo Side 0.5A 36-Pin DSO EP 制造商:Infineon Technologies AG 功能描述:ENGINECONTROL_IC - Tape and Reel 制造商:Infineon Technologies AG 功能描述:ENGINECONTROL_IC - Cut TR (SOS) 制造商:Infineon Technologies AG 功能描述:IC SW SMART OCTAL LOWSIDE PDSO36 |
| TLE6230GPNT | 制造商:Infineon Technologies AG 功能描述:Power Switch Lo Side 0.5A 36-Pin DSO T/R |
| TLE6230GPT | 制造商:Infineon Technologies AG 功能描述:Power Switch Lo Side 0.5A 36-Pin DSO T/R |
發布緊急采購，3分鐘左右您將得到回復。