- 您現在的位置：買賣IC網 > PDF目錄384007 > TLE4726 (INFINEON TECHNOLOGIES AG) 2-Phase Stepper-Motor Driver PDF資料下載
參數資料
| 型號： | TLE4726 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 2-Phase Stepper-Motor Driver |
| 中文描述： | 二相步進電機驅動器 |
| 文件頁數： | 21/23頁 |
| 文件大小： | 258K |
| 代理商： | TLE4726 |
TLE 4726
Data Sheet
21
1999-09-15
Application Hints
The TLE 4726 is intended to drive both phases of a stepper motor. Special care has
been taken to provide high efficiency, robustness and to minimize external components.
Power Supply
The TLE 4726 will work with supply voltages ranging from 5 V to 50 V at pin
V
S
. As the
circuit operates with chopper regulation of the current, interference generation problems
can arise in some applications. Therefore the power supply should be decoupled by a
0.22
μ
F ceramic capacitor located near the package. Unstabilized supplies may even
afford higher capacities.
Current Sensing
The current in the windings of the stepper motor is sensed by the voltage drop across
R
1
and
R
2
. Depending on the selected current internal comparators will turn off the sink
transistor as soon as the voltage drop reaches certain thresholds (typical 0 V, 0.25 V,
0.5 V and 0.75 V); (
R
1
,
R
2
= 1
). These thresholds are neither affected by variations
of
V
L
nor by variations of
V
S .
Due to chopper control fast current rises (up to 10 A/
μ
s) will occur at the sensing
resistors
R
1
and
R
2
. To prevent malfunction of the current sensing mechanism
R
1
and
R
2
should be pure ohmic. The resistors should be wired to GND as directly as possible.
Capacitive loads such as long cables (with high wire to wire capacity) to the motor should
be avoided for the same reason.
Synchronizing Several Choppers
In some applications synchrone chopping of several stepper motor drivers may be
desireable to reduce acoustic interference. This can be done by forcing the oscillator of
the TLE 4726 by a pulse generator overdriving the oscillator loading currents
(approximately
±
100
μ
A). In these applications low level should be between 0 V and 1 V
while high level should be between 2.6 V and
V
L
.
Optimizing Noise Immunity
Unused inputs should always be wired to proper voltage levels in order to obtain highest
possible noise immunity.
To prevent crossconduction of the output stages the TLE 4726 uses a special break
before make timing of the power transistors. This timing circuit can be triggered by short
glitches (some hundred nanoseconds) at the Phase inputs causing the output stage to
become high resistive during some microseconds. This will lead to a fast current decay
during that time. To achieve maximum current accuracy such glitches at the Phase
inputs should be avoided by proper control signals.
相關PDF資料 |
PDF描述 |
|---|---|
| TLE4726G | 2-Phase Stepper-Motor Driver |
| tle 4726 | 2-Phase Stepper-Motor Driver(兩相步進式馬達驅動器) |
| TLE4921-3U | Dynamic Differential Hall Effect Sensor IC(動態差分霍爾效應傳感器芯片) |
| TLE4923 | Dynamic Differential Hall Effect Sensor IC(動態差分霍爾效應傳感器芯片) |
| TLE4935L | Bipolar Hall IC Switches for Magnetic Field Applications(用于磁場應用的雙極霍爾芯片開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE4726G | 功能描述:馬達/運動/點火控制器和驅動器 2-Phase Stepper Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TLE4726G_08 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2-Phase Stepper-Motor Driver |
| TLE4726GGEG | 制造商:Infineon Technologies AG 功能描述:2 PHASE STEPPER, 0.7AMP, P-DSO-24 - Tape and Reel |
| TLE4726GNT | 制造商:Infineon Technologies AG 功能描述:Stepper Motor Controller 24-Pin DSO T/R |
| TLE4726GXUMA1 | 制造商:Infineon Technologies AG 功能描述:Stepper Motor Controller 24-Pin DSO 制造商:Infineon Technologies AG 功能描述:BODY BRIDGES - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC MOTOR DRIVER PAR 24DSO |
發布緊急采購，3分鐘左右您將得到回復。