參數資料
型號: tle 4729
廠商: SIEMENS AG
英文描述: 2-Phase Stepper-Motor Driver(兩相步進式馬達驅動器)
中文描述: 二相步進電機驅動器(兩相步進式馬達驅動器)
文件頁數: 23/26頁
文件大小: 222K
代理商: TLE 4729
Data Sheet
23
1999-06-24
TLE 4729 G
Application Hints
The TLE 4729 G is intended to drive both phases of a stepper motor. Special care has
been taken to provide high efficiency, robustness and to minimize external components.
Power Supply
The TLE 4729 G will work with supply voltages ranging from 5 V to 16 V at pin
V
S
. Surges
exceeding 16 V at
V
S
wont harm the circuit up to 45 V, but whole function is not
guaranteed. As soon as the voltage drops below approximately 16 V the TLE 4729 G
works promptly again.
As the circuit operates with chopper regulation of the current, interference generation
problems can arise in some applications. Therefore the power supply should be
decoupled by a 0.1
μ
F ceramic capacitor located near the package. Unstabilized
supplies may even afford higher capacities.
Inhibit Mode
In the case of low at all four current program inputs
I
XX the device will switch into inhibit
condition; the current consumption is reduced to very low values.
When starting operation again, i.e. putting at least one
I
XX to high potential, the Error 1
output signals an open load error if the corresponding phase input is high. The error is
reset by first recirculation in chop mode.
Current Sensing
The current in the windings of the stepper motor is sensed by the voltage drop across
R
sense
. Depending on the selected current internal comparators will turn off the sink
transistor as soon as the voltage drop reaches certain thresholds (typical 0 V, 0.07 V,
0.45 V and 0.7 V). These thresholds are not affected by variations of
V
S
. Consequently
instabilized supplies will not affect the performance of the regulation. For precise current
level it must be considered, that internal bounding wire (typ. 60 m
)
is a part of
R
sense
.
Due to chopper control fast current rises (up to 10 A/
μ
s) will occur at the sensing
resistors. To prevent malfunction of the current sensing mechanism
R
sense
should be
pure ohmic. The resistors should be wired to GND as directly as possible. Capacitive
loads such as long cables (with high wire to wire capacity) to the motor should be
avoided for the same reason.
Synchronizing Several Choppers
In some applications synchrone chopping of several stepper motor drivers may be
desirable to reduce acoustic interference. This can be done by forcing the oscillator of
the TLE 4729 G by a pulse generator overdriving the oscillator loading currents
(approximately
±
120
μ
A). In these applications low level should be between 0 V and
0.8 V while high level should between 3 V and 5 V.
相關PDF資料
PDF描述
tle 5205 5-A H-Bridge for DC-Motor Applications(5A、H橋型直流電機驅動器)
tle 5206 5-A H-Bridge for DC-Motor Applications(5A、H橋型直流電機驅動器)
tle 5208-6 1-A Hex-Half-Bridge / Double Six-Driver For Automotive and Industrial Motion Control Applications(1A、十六半橋/雙六-驅動器(六高邊、六低邊)用于汽車和工業的動作控制)
tle 5209 H-Bridge for DC-Motor Applications(H橋直流電機驅動器)
tle 5250 2.5-A High Performance Smart Power Stepper-Motor Driver with Diagnostic Interface(2.5A 高性能步進電機驅動器(帶診斷接口))
相關代理商/技術參數
參數描述
TLE4729G 功能描述:馬達/運動/點火控制器和驅動器 2-Ph Stepper Motor Driver; Bipolar RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TLE4729-G 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2-Phase Stepper-Motor Driver Bipolar-IC
TLE4729G_08 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2-Phase Stepper-Motor Driver Bipolar-IC
TLE4729GGEG 制造商:Infineon Technologies AG 功能描述:2-Phase Stepping Motor Driver 24-Pin DSO T/R
TLE4729GNT 制造商:Infineon Technologies AG 功能描述:STEPPER MOTOR CNTRLR 24PIN DSO - Tape and Reel 制造商:Infineon Technologies 功能描述:Infineon Technologies TLE4729GNT Motion Motor Controls