- 您現在的位置：買賣IC網 > PDF目錄98241 > TLC545IN (TEXAS INSTRUMENTS INC) 19-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP28 PDF資料下載
參數資料
| 型號： | TLC545IN |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 19-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 3/15頁 |
| 文件大?。?/td> | 202K |
| 代理商： | TLC545IN |
TLC545C, TLC545I, TLC546C, TLC546I
8-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 19 INPUTS
SLAS066B – DECEMBER 1985 – REVISED OCTOBER 1996
11
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
It is possible to connect SYSTEM CLOCK and I/O CLOCK together in special situations in which controlling circuitry
points must be minimized. In this case, the following special points must be considered in addition to the requirements
of the normal control sequence previously described.
1.
The first two clocks are required for this device to recognize CS is at a valid low level when the common clock
signal is used as an I/O CLOCK. When CS is recognized by the device to be at a high level, the common clock
signal is used for the conversion clock also.
2.
A low CS must be recognized before the I/O CLOCK can shift in an analog channel address. The device
recognizes a CS transition when the SYSTEM CLOCK terminal receives two positive edges and then a
negative edge. For this reason, after a CS negative edge, the first two clock cycles do not shift in the address.
Also, upon shifting in the address, CS must be raised after the eighth valid (10 total) I/O CLOCK. Otherwise,
additional common clock cycles are recognized as I/O CLOCKS and shift in an erroneous address.
For certain applications, such as strobing applications, it is necessary to start conversion at a specific point in time.
This device accommodates these applications. Although the on-chip sample and hold begins sampling upon the
negative edge of the fourth valid I/O clock cycle, the hold function is not initiated until the negative edge of the eighth
valid I/O clock cycle. Thus, the control circuitry can leave the I/O clock signal in its high state during the eighth valid
I/O clock cycle, until the moment at which the analog signal must be converted. The TLC545/546 continues sampling
the analog input until the eighth valid falling edge of the I/O clock. The control circuitry or software must then
immediately lower the I/O clock signal to initiate the hold function at the desired point in time and to start conversion.
相關PDF資料 |
PDF描述 |
|---|---|
| TLC548CP | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP8 |
| TLC548CD | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| TLC548ID | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| TLC548IDR | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| TLC548CDG4 | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC545ING4 | 功能描述:模數轉換器 - ADC 8B 76 kSPS ADC 19Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC546C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 19 INPUTS |
| TLC546I | 制造商:TI 制造商全稱:Texas Instruments 功能描述:8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 19 INPUTS |
| TLC546IFN | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述: |
| TLC546IN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。