- 您現在的位置：買賣IC網 > PDF目錄383953 > TLC32040MFK (Texas Instruments, Inc.) ANALOG INTERFACE CIRCUIT PDF資料下載
參數資料
| 型號： | TLC32040MFK |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | ANALOG INTERFACE CIRCUIT |
| 中文描述： | 模擬接口電路 |
| 文件頁數： | 9/30頁 |
| 文件大?。?/td> | 202K |
| 代理商： | TLC32040MFK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
TLC32040M
ANALOG INTERFACE CIRCUIT
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
4–9
power-up sequence
To ensure proper operation of the AIC and as a safeguard against latch-up, it is recommended that a Schottky
diode with a forward voltage less than or equal to 0.4 V be connected from V
CC–
to ANLG GND (see Figure 16).
In the absence of such a diode, power should be applied in the following sequence: ANLG GND and DGTL GND,
V
CC–
, then V
CC+
and V
DD
. Also, no input signal should be applied until after power up.
AIC responses to improper conditions
The AIC has provisions for responding to improper conditions. These improper conditions and the response of
the AIC to these conditions are presented in Table 1 below.
AIC register constraints
The following constraints are placed on the contents of the AIC registers:
1. TA register must be
≥
4 in WORD mode (WORD/BYTE = high).
2. TA register must be
≥
5 in BYTE mode (WORD/BYTE = low).
3. TA’ register can be either positive, negative, or zero.
4. RA register must be
≥
4 in WORD mode (WORD/BYTE = high).
5. RA register must be
≥
5 in BYTE mode (WORD/BYTE = low).
6. RA’ register can be either positive, negative, or zero.
7. (TA register
±
TA’ register) must be > 1.
8. (RA register
±
RA’ register) must be > 1.
9. TB register must be > 1.
Table 1. AIC Responses to Improper Conditions
IMPROPER CONDITION
TA register + TA’ register = 0 or 1
TA register – TA’ register = 0 or 1
TA register + TA’ register < 0
AIC RESPONSE
Reprogram TX Counter A with TA register value
MODULO 64 arithmetic is used to ensure that a positive value is loaded into the TX Counter A,
i.e., TA register + TA’ register + 40 HEX is loaded into TX Counter A.
Reprogram RX Counter A with RA register value
RA register + RA’ register = 0 or 1
RA register – RA’ register = 0 or 1
RA register + RA’ register = 0 or 1
MODULO 64 arithmetic is used to ensure that a positive value is loaded into the RX Counter
A, i.e., RA register + RA’ register + 40 HEX is loaded into RX Counter A.
AIC is shutdown.
TA register = 0 or 1
RA register = 0 or 1
TA register < 4 in WORD mode
TA register < 5 in BYTE mode
RA register < 4 in WORD mode
RA register < 5 in BYTE mode
TB register = 0 or 1
RB register = 0 or 1
AIC and DSP cannot communicate
The AIC serial port no longer operates.
Reprogram TB register with 24 HEX
Reprogram TB register with 24 HEX
Hold last DAC output
相關PDF資料 |
PDF描述 |
|---|---|
| TLC32040MJ | ANALOG INTERFACE CIRCUIT |
| TLC32044C | VOICE-BAND ANALOG INTERFACE CIRCUITS |
| TLC32045IN | VOICE-BAND ANALOG INTERFACE CIRCUITS |
| TLC32044E | VOICE-BAND ANALOG INTERFACE CIRCUITS |
| TLC32044I | VOICE-BAND ANALOG INTERFACE CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC32040MJ | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUIT |
| TLC32041C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUITS |
| TLC32041CFN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUITS |
| TLC32041CN | 制造商:TI 功能描述:32041 |
| TLC32041I | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUITS |
發布緊急采購，3分鐘左右您將得到回復。