參數資料
型號: TLC27L9MN
廠商: Texas Instruments, Inc.
英文描述: LinCMOSE PRECISION QUAD OPERATIONAL AMPLIFIERS
中文描述: LinCMOSE精密四運算放大器
文件頁數: 15/33頁
文件大?。?/td> 538K
代理商: TLC27L9MN
TLC27L2, TLC27L2A, TLC27L2B, TLC27L7
LinCMOS
PRECISION DUAL OPERATIONAL AMPLIFIERS
SLOS052B – OCTOBER 1987 – REVISED AUGUST 1994
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
full-power response
Full-power response, the frequency above which the operational amplifier slew rate limits the output voltage
swing, is often specified two ways: full-linear response and full-peak response. The full-linear response is
generally measured by monitoring the distortion level of the output while increasing the frequency of a sinusoidal
input signal until the maximum frequency is found above which the output contains significant distortion. The
full-peak response is defined as the maximum output frequency, without regard to distortion, above which full
peak-to-peak output swing cannot be maintained.
Because there is no industry-wide accepted value for significant distortion, the full-peak response is specified
in this data sheet and is measured using the circuit of Figure 1. The initial setup involves the use of a sinusoidal
input to determine the maximum peak-to-peak output of the device (the amplitude of the sinusoidal wave is
increased until clipping occurs). The sinusoidal wave is then replaced with a square wave of the same
amplitude. The frequency is then increased until the maximum peak-to-peak output can no longer be maintained
(Figure 5). A square wave is used to allow a more accurate determination of the point at which the maximum
peak-to-peak output is reached.
(d) f > BOM
(c) f = BOM
(b) BOM > f > 100 kHz
(a) f = 100 kHz
Figure 5. Full-Power-Response Output Signal
test time
Inadequate test time is a frequent problem, especially when testing CMOS high-volume, short-test-time
environment. Internal capacitances are inherently higher in CMOS devices and require longer test times than
their bipolar and BiFET counterparts. The problem becomes more pronounced with reduced supply levels and
lower temperatures.
相關PDF資料
PDF描述
TLC27L4Y LinCMOSE PRECISION QUAD OPERATIONAL AMPLIFIERS
TLC27M41 LinCMOSE PRECISION QUAD OPERATIONAL AMPLIFIERS
TLC27M41PW LinCMOSE PRECISION QUAD OPERATIONAL AMPLIFIERS
TLC27M4MD LinCMOSE PRECISION QUAD OPERATIONAL AMPLIFIERS
TLC27M4MFK LinCMOSE PRECISION QUAD OPERATIONAL AMPLIFIERS
相關代理商/技術參數
參數描述
TLC27M2ACD 功能描述:運算放大器 - 運放 LiNCMOS Dual RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TLC27M2ACD 制造商:Texas Instruments 功能描述:Operational Amplifier (Op-Amp) IC
TLC27M2ACDG4 功能描述:運算放大器 - 運放 LiNCMOS Dual RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TLC27M2ACDR 功能描述:運算放大器 - 運放 LinCMOS Precision Dual Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
TLC27M2ACDRG4 功能描述:運算放大器 - 運放 LinCMOS Precision Dual Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel