參數資料
型號： TLC1514ID
廠商： TEXAS INSTRUMENTS INC
元件分類： ADC
英文描述： 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16
封裝： GREEN, PLASTIC, SOIC-16
文件頁數： 8/37頁
文件大?。?/td> 572K
代理商： TLC1514ID
TLC1514, TLC1518
5-V, 10-BIT, 400 KSPS, 4/8 CHANNEL, LOW POWER,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN
SLAS252 – DECEMBER 1999
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
modes using the FIFO: modes 01, 10, 11 timing (continued)
Mode 10 (sweep mode) requires reconfiguration at the start of each new sweep sequence. Once the FIFO is
filled up to the programmed threshold, the host has the option to either read the FIFO or configure for other
modes. Once the FIFO is read, the host must reconfigure the device before the next sweep sequence can be
started. So the sequence is either configure : triggered conversions : FIFO read : configure. or configure :
triggered conversions : configure : .... Each configure clears the FIFO and the action that follows the configure
command depends on the mode setting of the device.
Mode 11 (repeat sweep mode) requires one cycle configuration. This sweep sequence can be repeated without
reconfiguration. Once the FIFO is filled up to the programmed threshold, the host has the option to either read
the FIFO or configure for other modes. So the sequence is either configure : triggered conversions : FIFO read
: triggered conversions : FIFO read ... or configure : triggered conversions : configure : .... Each configure clears
the FIFO and the action that follows the configure command depends on the mode setting of the device.
CS
CSTART
SDI
INT
SDO
From Channel 0
FS
(DSP)
From Channel 3
Configure
Conversion
Read FIFO
#1
#2
#3
#4
Top of FIFO
tsample(1)
Read FIFO
#1
From Channel 0
Conversion
From Channel 3
Conversion
Repeat
Second FIFO Read
Repeat
tsample(2)
tsample(3)
First FIFO Read
tconvert
tSample(i) > = MIN(tSample)
tsample(4)
Command = Configure write for mode 10 or 11, FIFO threshold = 1/2, sweep seq = 0–1–2–3.
Command = Read FIFO
Figure 12. TLC1514/TLC1518 Mode 10/11 DSP Serial Interface (conversions triggered by FS)
相關PDF資料
PDF描述
TLC1514IPW 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16
TLC1514IPWRG4 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16
TLC1514IDR 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16
TLC1518IPW 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLC1518IDWR 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
相關代理商/技術參數
參數描述
TLC1514ID 制造商:Texas Instruments 功能描述:IC 10BIT ADC 400KSPS SMD SOIC16 制造商:Texas Instruments 功能描述:IC, 10BIT ADC, 400KSPS, SMD, SOIC16
TLC1514IDG4 功能描述:模數轉換器 - ADC 10-Bit 400 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC1514IDR 功能描述:模數轉換器 - ADC 10-Bit 400 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC1514IDRG4 功能描述:模數轉換器 - ADC 10-Bit 400 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLC1514IPW 功能描述:模數轉換器 - ADC 10bit 400kSPS SAR RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*