- 您現在的位置：買賣IC網 > PDF目錄384981 > TL5209KTTR (Texas Instruments, Inc.) 500-mA LOW-NOISE LOW-DROPOUT VOLTAGE REGULATOR WITH SHUTDOWN PDF資料下載
參數資料
| 型號： | TL5209KTTR |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 500-mA LOW-NOISE LOW-DROPOUT VOLTAGE REGULATOR WITH SHUTDOWN |
| 中文描述： | 500 - mA的低噪音低，具有關斷穩壓器 |
| 文件頁數： | 18/22頁 |
| 文件大?。?/td> | 359K |
| 代理商： | TL5209KTTR |
www.ti.com
APPLICATION INFORMATION
Enable/Shutdown
The enable function is only available in the SOIC (D) and TO-263 (KTT) packages. The EN pin is CMOS-logic
compatible. When EN is held high (>2 V), the regulator is active. Likewise, applying a low signal (<0.4 V at
25
°
C) to EN or leaving it open shuts down the regulator. If the enable/shutdown feature is not needed, EN
should be tied to V
IN
.
Input Capacitor
If the input of the regulator is located more than ten inches from the power-supply filter, or if a battery is used to
power the regulator, a minimum 1-
μ
F input capacitor is recommended.
Output Capacitor
As with all PNP regulators, an output capacitor is needed for stability. The required minimum size of this output
capacitor depends on several factors, one of which is whether a bypass capacitor is used.
With no bypass capacitor, a minimum C
OUT
of 1
μ
F is recommended.
With a bypass capacitor of 470 pF (see
Figure 6
), a minimum C
OUT
of 2.2
μ
F is recommended.
Larger values of C
OUT
are beneficial, because they improve the regulator transient response.
Another factor that can determine the minimum size of the output capacitor is the load current. At low loads, a
smaller output capacitor is needed for stability.
Bypass Capacitor
An optional bypass capacitor, C
BYP
, can be externally connected to the regulator via the BYP pin for improved
noise performance (only for SOIC and TO-263 packages). Connected to the internal voltage divider and the
error amplifier of the regulator, this bypass capacitor filters the noise of the internal reference and reduces the
noise effects on the error amplifier. The overall result is a significant drop in output noise of the regulator. A
470-pF bypass capacitor is recommended.
Low-Voltage Operation
When using the TL5209-18 and TL5209-25 in voltage-sensitive applications, special considerations are required.
If appropriate output and bypass capacitors are not chosen properly, these devices may experience a temporary
overshoot of their nominal voltages.
TL5209
500-mA LOW-NOISE LOW-DROPOUT VOLTAGE REGULATOR
WITH SHUTDOWN
SLVS581–SEPTEMBER 2006
The equivalent series resistance (ESR) of the output capacitor also can affect regulator stability. C
OUT
should
have an ESR of
≈
1
, and it should have a resonant frequency above 1 MHz. Too low an ESR can cause the
output to have a low-amplitude oscillation and/or underdamped transient response. Most tantalum or aluminum
electrolytic capacitors can be used for the output capacitors. However, care should be used at low temperatures,
because aluminum electrolytics use electrolytes that can freeze at low temperature (
≈
–30
°
C). Solid tantalum
capacitors do not exhibit this problem and should be used below –25
°
C.
Adding a bypass capacitor has several effects on the regulator that must be taken into account. First, the bypass
capacitor reduces the phase margin of the regulator and, thus, the minimum C
OUT
needs to be increased to 2.2
μ
F, as previously mentioned. Second, upon startup of the regulator, the bypass capacitor has an effect on the
regulator turn-on time. If a slow ramp-up of the output is needed, larger values of C
BYP
should be used.
Conversely, if a fast ramp-up of the output is needed, use a smaller C
BYP
or none at all.
If a bypass capacitor is not needed, BYP should be left open.
At start-up, the full input voltage is initially applied across the regulator pass transistor, causing it to be
temporarily fully turned on. By contrast, the error amplifier and voltage-reference circuits, being powered from
the output, are not powered up as fast. In order to slow down the output ramp and give the error amplifier time to
respond, select larger values of output and bypass capacitors. The longer ramp time of the output allows the
regulator enough time to respond and keeps the output from overshooting its nominal value.
To prevent an overshoot when starting up into a light load (
≈
100
μ
A), 4.7-
μ
F and 470-pF capacitors are
recommended for the output and bypass capacitors, respectively. At higher loads, 10-
μ
F and 470-pF capacitors
should be used.
18
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| TL5501CN | 6-BIT ANALOG-TO-DIGITAL CONVERTER |
| TL5501N | 6-BIT ANALOG-TO-DIGITAL CONVERTER |
| TL5580IPWE4 | DUAL LOW-NOISE WIDE-BANDWIDTH PRECISION AMPLIFIER |
| TL592 | DIFFERENTIAL VIDEO AMPLIFIER |
| TL592BD14 | DIFFERENTIAL VIDEO AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TL-521 | 制造商:Ideal Industries Inc 功能描述:TEST LEADS FOR 61-521 |
| TL5242 | 制造商:Tadiran Batteries 功能描述:LITHIUM BATTERY, 3.6V; Battery Size Code:-; Battery Capacity:2.1Ah; Battery Voltage:3.6V; Battery Technology:Lithium; Battery Terminals:Connector; External Height:16.7mm; External Width:61mm; External Depth:18.1mm; Depth:0.83" ;RoHS Compliant: NA |
| TL-5242 | 制造商:Tadiran Batteries 功能描述:Battery; Lithium; 3-Pin Connector; 3.6V; 24AWG; 2.1Ah; Hook & Loop Fastener 制造商:Tadiran Batteries 功能描述:TL Series 3.6 V 2.1 Ah Lithium Battery Pack with 3 Pin Connector |
| TL5242/W | 制造商:Tadiran Batteries 功能描述:LITHIUM BATTERY, 3.6V; Battery Size Code:-; Battery Capacity:2.1Ah; Battery Voltage:3.6V; Battery Technology:Lithium; Battery Terminals:Connector; External Height:16.7mm; External Width:61mm; External Depth:18.1mm; Depth:0.83" ;RoHS Compliant: NA |
| TL-5242/W | 功能描述:BATTERY PAK LITH 3.6V LEADS/CONN RoHS:是 類別:電池產品 >> 電池組 系列:- MSDS 材料安全數據表:Nickel Cadmium Battery MSDS 標準包裝:1 系列:Cadnica 電池化學:鎳鎘 可充電:是 電池大小:D 單元數:10 電壓 - 額定:12V 容量:4Ah 結構:正面至背面，5 排 x 2 芯電池 端接類型:焊片 尺寸/尺寸:6.42" L x 1.28" W x 4.63" H（163.0mm x 32.6mm x 117.6mm） 重量:3.5 磅（1.6kg） 請注意:- 配用:SY125-ND - BATT NICAD 1.2V D 4000MAH 其它名稱:SY125-L025 |
發布緊急采購，3分鐘左右您將得到回復。