參數資料
型號: TL500
廠商: Texas Instruments, Inc.
英文描述: PULSE-WIDTH-MODULATION CONTROL CIRCUITS
中文描述: 脈寬調制控制電路
文件頁數: 3/23頁
文件大?。?/td> 348K
代理商: TL500
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084E – APRIL 1994 – REVISED OCTOBER 1999
3
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description
voltage reference
A 2.5-V regulator operating from V
CC
is used to power the internal circuitry of the TL5001 and TL5001A and
as a reference for the error amplifier and SCP circuits. A resistive divider provides a 1-V reference for the error
amplifier noninverting input which typically is within 2% of nominal over the operating temperature range.
error amplifier
The error amplifier compares a sample of the dc-to-dc converter output voltage to the 1-V reference and
generates an error signal for the PWM comparator. The dc-to-dc converter output voltage is set by selecting
the error-amplifier gain (see Figure 1), using the following expression:
V
O
= (1 + R1/R2) (1 V)
To PWM
Comparator
Vref = 1 V
4
VI(FB)
3
+
R2
R1
COMP
FB
Compensation
Network
TL5001/A
GND
8
Figure 1. Error-Amplifier Gain Setting
The error-amplifier output is brought out as COMP for use in compensating the dc-to-dc converter control loop
for stability. Because the amplifier can only source 45
μ
A, the total dc load resistance should be 100 k
or more.
oscillator/PWM
The oscillator frequency (f
osc
) can be set between 20 kHz and 500 kHz by connecting a resistor between RT
and GND. Acceptable resistor values range from 15 k
to 250 k
. The oscillator frequency can be determined
by using the graph shown in Figure 5.
The oscillator output is a triangular wave with a minimum value of approximately 0.7 V and a maximum value
of approximately 1.3 V. The PWM comparator compares the error-amplifier output voltage and the DTC input
voltage to the triangular wave and turns the output transistor off whenever the triangular wave is greater than
the lesser of the two inputs.
dead-time control (DTC)
DTC provides a means of limiting the output-switch duty cycle to a value less than 100%, which is critical for
boost and flyback converters. A current source generates a reference current (I
DT
) at DTC that is nominally
equal to the current at the oscillator timing terminal, RT. Connecting a resistor between DTC and GND generates
a dead-time reference voltage (V
DT
), which the PWM/DTC comparator compares to the oscillator triangle wave
as described in the previous section. Nominally, the maximum duty cycle is 0% when V
DT
is 0.7 V or less and
100% when V
DT
is 1.3 V or greater. Because the triangle wave amplitude is a function of frequency and the
source impedance of RT is relatively high (1250
), choosing R
DT
for a specific maximum duty cycle, D, is
accomplished using the following equation and the voltage limits for the frequency in question as found in
Figure 11 (V
osc
max and V
osc
min are the maximum and minimum oscillator levels):
相關PDF資料
PDF描述
TL5001AJG JT 66C 66#22D SKT PLUG
TL5001JG PULSE-WIDTH-MODULATION CONTROL CIRCUITS
TL5001ACP PULSE-WIDTH-MODULATION CONTROL CIRCUITS
TL5001AD PULSE-WIDTH-MODULATION CONTROL CIRCUITS
TL5001AFK PULSE-WIDTH-MODULATION CONTROL CIRCUITS
相關代理商/技術參數
參數描述
TL5000DCJ 制造商:Opnext 功能描述:FULL C-BAND TUNABLE (INTEGRABLE TUNABLE LASER ASSEMBLY) - Tape and Reel
TL5000DLJ 制造商:BOOKHAM 制造商全稱:Bookham, Inc. 功能描述:LambdaFLEX⑩ iTLA TL5000 Integrable Tunable Laser Assembly
TL5000VCJ 制造商:BOOKHAM 制造商全稱:Bookham, Inc. 功能描述:LambdaFLEX⑩ iTLA Integrable Tunable Laser Assembly with variable output power
TL5000VLJ 制造商:BOOKHAM 制造商全稱:Bookham, Inc. 功能描述:LambdaFLEX⑩ iTLA Integrable Tunable Laser Assembly with variable output power
TL5001 功能描述:LED 安裝硬件 TowerLight, 50mm Short Base, Plastic RoHS:否 制造商:Bivar 產品:LED Mounting Clips LED 大小:5 mm 材料:Nylon 顏色:Black 主體長度:4.4 mm 面板厚度尺寸: 封裝:Bulk