- 您現在的位置：買賣IC網 > PDF目錄384001 > TL1454ACNS (Texas Instruments, Inc.) DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT PDF資料下載
參數資料
| 型號： | TL1454ACNS |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| 中文描述： | 雙通道脈寬調制（PWM）控制電路 |
| 文件頁數： | 5/27頁 |
| 文件大小： | 409K |
| 代理商： | TL1454ACNS |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
TL1454A, TL1454AY
DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM)
CONTROL CIRCUIT
SLVS423 A
–
MAY 2002
–
REVISED SEPTEMBER 2002
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
error amplifier
R1 and R2 should be tight-tolerance (
±
1% or better) devices with low and/or matched temperature coefficients
to minimize output voltage errors. A device with a
±
5% tolerance is suitable for R3.
_
+
IN
–
IN+
R2
COMP
To PWM
VO
Compensation
Network
REF
R1
R3
Converter
Output
Figure 2. Sense Divider/Error Amplifier Configuration for Converters with Negative Outputs
Figure 2 shows the divider network and error-amplifier configuration for negative output voltages. In general,
the comments for positive output voltages also apply for negative outputs. The output voltage is given by:
VO
R1Vref
R2
The design procedure for choosing the resistor value is to select a convenient value for R2 (instead of R3 in
the procedure for positive outputs) and calculate R1 and R3 using:
R1
R2VO
Vref
R3
R1R2
R1
R2
Values in the 10-k
to 20-k
range work well for R2. R3 can be omitted and the noninverting amplifier connected
to ground in applications where the output voltage tolerance is not critical.
oscillator
The oscillator frequency can be set between 50 kHz and 2 MHz with a resistor connected between RT and GND
and a capacitor between CT and GND (see Figure 3). Figure 6 is used to determine R
T
and C
T
for the desired
operating frequency. Both components should be tight-tolerance, temperature-stable devices to minimize
frequency deviation. A 1% metal-film resistor is recommended for R
T
, and a 10%, or better, NPO ceramic
capacitor is recommended for C
T
.
RT
CT
RT
2
CT
1
TL1454A
Figure 3. Oscillator Timing
相關PDF資料 |
PDF描述 |
|---|---|
| TL1454AY | DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
| TL1593CNS | 780- 】 488-pixel ccd image sensor |
| TL2575_08 | 1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATORS |
| TL2575ADJI | 1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATORS |
| TL2575HV | 1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TL1454ACNSR | 功能描述:DC/DC 開關控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TL1454ACNSRG4 | 功能描述:DC/DC 開關控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TL1454ACPW | 功能描述:DC/DC 開關控制器 Dual-Ch PWM Control Circuit RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TL1454ACPWG4 | 功能描述:DC/DC 開關控制器 Dual-Ch PWM Control Circuit RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TL1454ACPWR | 功能描述:DC/DC 開關控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。