參數資料
型號: TK70403M
廠商: TOKO INC
元件分類: 基準電壓源/電流源
英文描述: 1.03 V REGULATOR WITH ON/OFF SWITCH
中文描述: FIXED POSITIVE LDO REGULATOR, 0.06 V DROPOUT, PDSO6
封裝: PLASTIC, SOT-23, SOT-26, 6 PIN
文件頁數: 6/10頁
文件大?。?/td> 61K
代理商: TK70403M
Page 6
January 1999 TOKO, Inc.
TK70403
DEFINITION AND EXPLANATION OF TECHNICAL TERMS
OUTPUT VOLTAGE (V
OUT
)
The output voltage is specified with V
IN
= V
OUT(TYP)
+ 0.4
and I
OUT
= 2 mA.
DROPOUT VOLTAGE (V
DROP
)
The dropout voltage is the difference between the input
voltage and the output voltage, at which point the regulator
starts to fall out of regulation. Below this value, the output
voltage will fall as the input value is reduced. It is dependent
upon the load current and the temperature.
OUTPUT CURRENT (I
OUT(MAX)
)
The rated output current is specified under the condition
where the output voltage drops 0.4 V when the output
current is loaded. The input voltage is set to V
OUT
+ 0.4 V.
LINE REGULATION (Line Reg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
voltage is pulsed to minimize temperature effects.
LOAD REGULATION (Load Reg)
Load regulation is the ability of the regulator to maintain a
constant output voltage as the load current changes. It is
pulsed to minimize temperature effects. The load regulation
is specified to 0.1 mA to 5.0 mA.
QUIESCENT CURRENT (I
Q
)
The quiescent current is the current which flows through
the ground terminal under no load conditions (I
OUT
= 0 mA).
GROUND CURRENT (I
GND
)
Ground current is the current which flows through the
ground pin(s). It is defined as I
IN
- I
OUT
, excluding control
current.
RIPPLE REJECTION (RR)
Ripple rejection is the ability of the regulator to attenuate
the ripple content of the input voltage at the output. It is
specified with 50 mVp-p, 400 Hz, I
OUT
= 2 mA superimposed
on the input voltage, where V
IN
= V
OUT(TYP)
+ 0.4 V. The
ripple rejection is the ratio of the output vs. input and is
expressed in dB.
ON/OFF CONTROL
High is “on” (referenced to ground). When the on/off
function is not used, connect the control terminal to V
IN
.
The control current can be reduced by inserting a series
resistor (R
CONT
) between the control terminal and V
IN
.
Changes in the on/off level, due to this connection, are
shown below.
ON/OFF RESPONSE WITH CONTROL (SPEED)
The turn-on time depends upon the value of the output
capacitor and the noise bypass capacitor. The turn-on time
will decrease with smaller value of either capacitor. The
graph below shows the relationship between turn-on time
and load capacitance. However, when the capacitance is
small, load transient and line transient will worsen and the
noise will increase. C
L
= 0.68
μ
F, C
N
= 1000 pF will be the
best for fastest operation.
VCONT (V)
I
2
0 1 2
1
0
VOUT = 1 M
RCONT = 820 k
VOUT = 680 k
RISE TIME (μs)
C
.1 μ
0 100 1000
.01 μ
0
CL = 2.2 μF
1000 pF
100 pF
10 pF
CL = 0.45 μF
CL = 4.7 μF
CL = 0.68 μF
相關PDF資料
PDF描述
TK70403MTB 1.03 V REGULATOR WITH ON/OFF SWITCH
TK71125 Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
TK71120 Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
TK71150 Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
TK71130 Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
相關代理商/技術參數
參數描述
TK70403MTB 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:1.03 V REGULATOR WITH ON/OFF SWITCH
TK70403MTB/03J 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:1.03 V REGULATOR WITH ON/OFF SWITCH
TK70A06J1 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Switching Regualtor Application
TK70A06J1(Q) 功能描述:MOSFET MOSFET N-Ch 60V 70A RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS(導通):0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube
TK70D06J1 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Switching Regulator Application