- 您現在的位置：買賣IC網 > PDF目錄361482 > TK11930 (TOKO Inc.) VOLTAGE REGULATOR WITH RESET OUTPUT PDF資料下載
參數資料
| 型號： | TK11930 |
| 廠商： | TOKO Inc. |
| 英文描述： | VOLTAGE REGULATOR WITH RESET OUTPUT |
| 中文描述： | 調壓器RESET輸出 |
| 文件頁數： | 19/23頁 |
| 文件大?。?/td> | 134K |
| 代理商： | TK11930 |
January 1999 TOKO, Inc.
Page 19
TK119xx
PACKAGE POWER DISSIPATION (P
D
)
This is the power dissipation level at which the thermal
sensor is activated. The IC contains an internal thermal
sensor which monitors the junction temperature. When
the junction temperature exceeds the monitor threshold of
150
°
C, the IC is shut down. The junction temperature
rises as the difference between the input power (V
IN
x I
IN
)
and the output power (V
OUT
x I
OUT
) increases. The rate of
temperature rise is greatly affected by the mounting pad
configuration on the PCB, the board material, and the
ambient temperature. When the IC mounting has good
thermal conductivity, the junction temperature will be low
even if the power dissipation is great. When mounted on
the recommended mounting pad, the power dissipation of
the SOT-23L is increased to 400 mW. For operation at
ambient temperatures over 25
°
C, the power dissipation of
the SOT-23L device should be derated at 3.2 mW/
°
C. To
determine the power dissipation for shutdown when
mounted, attach the device on the actual PCB and
deliberately increase the output current (or raise the input
voltage) until the thermal protection circuit is activated.
Calculate the power dissipation of the device by subtracting
the output power from the input power. These
measurements should allow for the ambient temperature
of the PCB. The value obtained from P
D
/(150
°
C - T
A
) is the
derating factor. The PCB mounting pad should provide
maximum thermal conductivity in order to maintain low
device temperatures. As a general rule, the lower the
temperature, the better the reliability of the device. The
thermal resistance when mounted is expressed as follows:
T
j
= 0
jA
x P
D
+ T
A
For Toko ICs, the internal limit for junction temperature is
150
°
C. If the ambient temperature (T
A
) is 25
°
C, then:
150
°
C = 0
jA
x P
D
+ 25
°
C
0
jA
= 125
°
C/ P
D
P
D
is the value when the thermal sensor is activated. A
simple way to determine P
D
is to calculate V
IN
x I
IN
when
the output side is shorted. Input current gradually falls as
temperature rises. You should use the value when thermal
equilibrium is reached.
DEFINITION AND EXPLANATION OF TECHNICAL TERMS
QUIESCENT CURRENT (I
Q
)
The quiescent current is the current which flows through
the ground terminal under no load conditions (I
OUT
= 0 mA).
GROUND CURRENT (I
GND
)
Ground current is the current which flows through the
ground pin(s). It is defined as I
IN
- I
OUT
, excluding control
current.
LINE REGULATION (LINE REG)
Line regulation is the relationship between change in
output voltage due to a change in input voltage.
LOAD REGULATION (LOAD REG)
Load regulation is the relationship between change in
output voltage due to a change in load current.
DROPOUT VOLTAGE (V
DROP
)
This is a measure of how well the regulator performs as the
input voltage decreases. The smaller the number, the
further the input voltage can decrease before regulation
problems occur. Nominal output voltage is first measured
when V
IN
= V
OUT(TYP)
+ 1 at a chosen load current. When
the output voltage has dropped 100 mV from the nominal,
V
IN
- V
OUT
is the dropout voltage. This voltage is affected
by load current and junction temperature.
OUTPUT NOISE VOLTAGE
This is the effective AC voltage that occurs on the output
voltage under the condition where the input noise is low
and with a given load, filter capacitor, and frequency
range.
THERMAL PROTECTION
This is an internal feature which turns the regulator off
when the junction temperature rises above 150
°
C. After
the regulator turns off, the temperature drops and the
regulator output turns back on. Under certain conditions,
the output waveform may appear to be an oscillation as the
output turns off and on and back again in succession.
相關PDF資料 |
PDF描述 |
|---|---|
| TK11930MTL | VOLTAGE REGULATOR WITH RESET OUTPUT |
| TK11932 | VOLTAGE REGULATOR WITH RESET OUTPUT |
| TK11932MTL | VOLTAGE REGULATOR WITH RESET OUTPUT |
| TK11935 | VOLTAGE REGULATOR WITH RESET OUTPUT |
| TK11935MTL | VOLTAGE REGULATOR WITH RESET OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TK11950MTL | 制造商:TOKO 功能描述: |
| TK119A | 制造商:Thomas & Betts 功能描述:3 1/2" COUPLING,COMP.,EMT,STL 制造商:Thomas & Betts 功能描述:Fittings Coupler 3.5inch Steel |
| TK119A-RT | 制造商:Thomas & Betts 功能描述:3 1/2 IN RAINTIGHT COMPRESSION CPL |
| TK11A45D(Q) | 制造商:Toshiba America Electronic Components 功能描述: |
| TK11A45D(STA4,Q,M) | 功能描述:MOSFET N-Ch MOS 10A 40V 25W 410pF 0.029 RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。