參數資料
型號: TK113XXBM
廠商: TOKO INC
元件分類: 基準電壓源/電流源
英文描述: VOLTAGE REGULATOR WITH ON/OFF SWITCH
中文描述: FIXED POSITIVE REGULATOR, PDSO6
封裝: SOT-23L, 6 PIN
文件頁數: 11/13頁
文件大?。?/td> 152K
代理商: TK113XXBM
May, 1997 TOKO, Inc.
Page 11
TK113xxB
PACKAGE POWER DISSIPATION (P
D
)
This is the power dissipation level at which the thermal sensor is activated. The IC contains an internal thermal sensor
which monitors the junction temperature. When the junction temperature exceeds the monitor threshold of 150
°
C, the
IC is shutdown. The junction temperature rises as the difference between the input power (V
IN
X I
IN
) and the output power
(V
OUT
X I
OUT
) increases. The rate of temperature rise is greatly affected by the mounting pad configuration on the PCB,
the board material, and the ambient temperature. When the IC mounting has good thermal conductivity, the junction
temperature will be low even if the power dissipation is great. When mounted on the recommended mounting pad, the
power dissipation of the SOT-23L is increased to 600 mW. For operation at ambient temperatures over 25
°
C, the power
dissipation of the SOT-23L device should be derated at 4.8 mW/
°
C. The power dissipation of the SOT-89-5 package is
900 mW when mounted as recommended. Derate the power dissipation at 7.2 mW/
°
C for operation above 25
°
C. To
determine the power dissipation for shutdown when mounted, attach the device on the actual PCB and deliberately
increase the output current (or raise the input voltage) until the thermal protection circuit is activated. Calculate the power
dissipation of the device by subtracting the output power from the input power. These measurements should allow for the
ambient temperature of the PCB. The value obtained from PD/(150
°
C - T
A
) is the derating factor. The PCB mounting
pad should provide maximum thermal conductivity in order to maintain low device temperatures. As a general rule, the
lower the temperature, the better the reliability of the device. The Thermal resistance when mounted is expressed as
follows:
T
J
= 0
JA
X P
D
+ T
A
For Toko ICs, the internal limit for junction temperature is 150
°
C. If the ambient temperature, T
A
is 25
°
C, then:
150
°
C = 0
JA
X P
D
+ 25
°
C
0
JA
X P
D
= 125
°
C
0
JA
= 125
°
C/ P
D
P
D
is the value when the thermal sensor is activated. A simple way to determine PD is to calculate V
IN
X I
IN
when the output
side is shorted. Input current gradually falls as temperature rises. You should use the value when thermal equilibrium is
reached.
The range of currents usable can also be found from the graph below.
Procedure:
1.) Find P
D
2.) P
D1
is taken to be P
D
X (
0.8 ~ 0.9)
3.) Plot P
D1
against 25
°
C
4.) Connect P
D1
to the point corresponding to the 150
°
C with a straight line.
5.) In design, take a vertical line from the maximum operating temperature (e.g. 75
°
C) to the derating curve.
6.) Read off the value of P
D
against the point at which the vertical line intersects the derating curve. This is taken as the
maximum power dissipation, D
PD
.
DEFINITION AND EXPLANATION OF TECHNICAL TERMS (CONT.)
PD
Dpd
25
50
75
150
(mW)
T (°C)
3
6
5
4
相關PDF資料
PDF描述
TK11324BUCB Sealed illuminated pushbutton switch with flush mount options
TK11334BUCB VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11344BUCB Pushbutton switch features latching or momentary functions with a variety of housing styles
TK11324BUCL VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11334BUCL SWITCH PB 4PDT MOMENTARY
相關代理商/技術參數
參數描述
TK11445MTL 制造商:TOKO Inc 功能描述:
TK11450MTL 制造商:TOKO Inc XXX 功能描述:Voltage Regulator, +5V, Bi-Polar, 6 Pin, Plastic, TSOP
TK114A 制造商:Thomas & Betts 功能描述:Fittings Coupler 1.25inch Steel
TK114A-RT 制造商:Thomas & Betts 功能描述:Fittings Coupler 1.25inch Steel
TK114US 制造商:Thomas & Betts 功能描述:SG TK114US 1 1/4 IN EMT COMPRESSION