參數資料
型號: TK11129S
廠商: TOKO Inc.
英文描述: VOLTAGE REGULATOR WITH ON/OFF SWITCH
中文描述: 調壓器ON / OFF開關
文件頁數: 11/16頁
文件大?。?/td> 84K
代理商: TK11129S
March 1999 TOKO, Inc.
Page 11
TK111xxS
PACKAGE POWER DISSIPATION (P
D
)
This is the power dissipation level at which the thermal
sensor is activated. The IC contains an internal thermal
sensor which monitors the junction temperature. When the
junction temperature exceeds the monitor threshold of
150
°
C, the IC is shut down. The junction temperature
rises as the difference between the input power (V
IN
x I
IN
)
and the output power (V
OUT
x I
OUT
) increases. The rate of
temperature rise is greatly affected by the mounting pad
configuration on the PCB, the board material, and the
ambient temperature. When the IC mounting has good
thermal conductivity, the junction temperature will be low
even if the power dissipation is great. When mounted on
the recommended mounting pad, the power dissipation of
the SOT-23-5 is increased to 500 mW. For operation at
ambient temperatures over 25
°
C, the power dissipation of
the SOT-23-5 device should be derated at 4.0 mW/
°
C. To
determine the power dissipation for shutdown when
mounted, attach the device on the actual PCB and
deliberately increase the output current (or raise the input
voltage) until the thermal protection circuit is activated.
Calculate the power dissipation of the device by subtracting
the output power from the input power. These
measurements should allow for the ambient temperature
of the PCB. The value obtained from P
D
/(150
°
C - T
A
) is the
derating factor. The PCB mounting pad should provide
maximum thermal conductivity in order to maintain low
device temperatures. As a general rule, the lower the
temperature, the better the reliability of the device. The
thermal resistance when mounted is expressed as follows:
T
j
= 0
jA
x P
D
+ T
A
For Toko ICs, the internal limit for junction temperature is
150
°
C. If the ambient temperature (T
A
) is 25
°
C, then:
150
°
C = 0
jA
x P
D
+ 25
°
C
0
jA
= 125
°
C/ P
D
P
D
is the value when the thermal sensor is activated. A
simple way to determine P
D
is to calculate V
IN
x I
IN
when
the output side is shorted. Input current gradually falls as
temperature rises. You should use the value when thermal
equilibrium is reached.
The range of usable currents can also be found from the
graph below.
Procedure:
1)
2)
3)
4)
Find P
D
P
D1
is taken to be P
D
x (~ 0.8 - 0.9)
Plot P
D1
against 25
°
C
Connect P
D1
to the point corresponding to the 150
°
C
with a straight line.
In design, take a vertical line from the maximum
operating temperature (e.g., 75
°
C) to the derating
curve.
Read off the value of P
D
against the point at which the
vertical line intersects the derating curve. This is taken
as the maximum power dissipation, D
PD
.
5)
6)
SOT-23-5 POWER DISSIPATION CURVE
0 50 100 150
TA (
°
C)
P
0
0.6
1.0
0.2
0.4
0.8
MOUNTED AS
SHOWN
FREE AIR
PD
DPD
25
50
75
150
(mW)
TA ( C)
3
6
5
4
DEFINITION AND EXPLANATION OF TECHNICAL TERMS (CONT.)
相關PDF資料
PDF描述
TK11132S VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11133S VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11134S VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11141S VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11142S VOLTAGE REGULATOR WITH ON/OFF SWITCH
相關代理商/技術參數
參數描述
TK11129SCL 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11129SIL 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11130CSCL-G 功能描述:IC REG LDO 3V .2A SOT23-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:50 系列:- 穩壓器拓?fù)浣Y(jié)構:正,固定式 輸出電壓:24V 輸入電壓:最高 40 V 電壓 - 壓降(標準):2V @ 350mA 穩壓器數量:1 電流 - 輸出:500mA 電流 - 限制(最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220AB 包裝:管件 其它名稱:MC78M24BTG-NDMC78M24BTGOS
TK11130M 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:VOLTAGE REGULATOR WITH ON/OFF SWITCH
TK11130MCL 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:VOLTAGE REGULATOR WITH ON/OFF SWITCH