- 您現在的位置：買賣IC網 > PDF目錄365786 > TJA1050 (NXP Semiconductors N.V.) CAN High-Speed Transceiver(CAN高速收發器) PDF資料下載
參數資料
| 型號： | TJA1050 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | CAN High-Speed Transceiver(CAN高速收發器) |
| 中文描述： | CAN高速收發器（的CAN高速收發器） |
| 文件頁數： | 10/31頁 |
| 文件大小： | 254K |
| 代理商： | TJA1050 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
TJA1050 - CAN High-Speed Transceiver
Application Note
AN00020
Philips Semiconductors
10
so-called dominant signal level on the bus lines (see Figure 2.3). The output driver CANH provides a
source output from V
and the output driver CANL a sink output towards GND. As an example Figure
2.2 shows the block diagram of the TJA1050.
The bus is in recessive state if no bus node transmits a dominant bit. If one or multiple bus nodes transmit
a dominant bit, the bus lines enter the dominant state thus overriding the recessive state (wired-AND
characteristic).
The receiver comparator converts the differential bus signal to a logic level signal, which is output at RxD.
The serial receive data stream is provided to the bus protocol controller for decoding. The receiver
comparator is always active i.e. it monitors the bus while the bus node is transmitting a message. This is
required to support the non-destructive bit by bit arbitration scheme of CAN.
Typically the bus is set up with a pair of twisted wires. Considering a linear topology specified in
ISO11898 the two bus ends are terminated with a resistor of nominal 120
. This results in the required
bus load of nominal 60
. Close matching of the termination resistor with the cable impedance ensures
that data signals will not be reflected at the bus ends.
'ULYHU
9UHI
9
&&
7HPS
3URWHFWLRQ
7['
7LPHRXW
7LPHU
9
&&
9
&&
7['
5['
9UHI
6
9
&&
&$1+
&$1/
*1'
9
&&
Figure 2.2: Block diagram of the TJA1050
相關PDF資料 |
PDF描述 |
|---|---|
| TJA1053 | Fault-tolerant CAN transceiver(容錯CAN收發器) |
| TJA1054 | Fault-tolerant CAN transceiver(容錯CAN收發器) |
| TK1-L2-1.5V | ULTRA LOW PROFILE 2 AMP. POLARIZED RELAY |
| TK1-L2-12V | ULTRA LOW PROFILE 2 AMP. POLARIZED RELAY |
| TK1-L2-24V | ULTRA LOW PROFILE 2 AMP. POLARIZED RELAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TJA1050T | 制造商:NXP Semiconductors 功能描述: 制造商:NXP Semiconductors 功能描述:LAN Transceiver, Single, 8 Pin, Plastic, SOP |
| TJA1050T/CM,118 | 功能描述:CAN 接口集成電路 RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TJA1050T/H/V,112 | 功能描述:網絡控制器與處理器 IC CAN 1MBd Silent 5V 8-Pin RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1050T/H/V,118 | 功能描述:網絡控制器與處理器 IC CAN 1MBd Silent 5V 8-Pin RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| TJA1050T/N,112 | 功能描述:網絡控制器與處理器 IC HIGH SPEED CAN TRANSCEIVER RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。