- 您現在的位置：買賣IC網 > PDF目錄384000 > TISP7380F3SL (BOURNS INC) MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS PDF資料下載
參數資料
| 型號： | TISP7380F3SL |
| 廠商： | BOURNS INC |
| 元件分類： | 浪涌電流限制器 |
| 英文描述： | MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| 中文描述： | 380 V, 7.1 A, SILICON SURGE PROTECTOR |
| 封裝： | SIP-3 |
| 文件頁數： | 17/19頁 |
| 文件大?。?/td> | 562K |
| 代理商： | TISP7380F3SL |
MARCH 1994 - REVISED MARCH 2006
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
APPLICATIONS INFORMATION
1.2/50 Generators (continued)
Lightning Surge (continued)
Impulse Testing
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table in this section shows some common test values.
TISP7xxxF3 (MV, HV) Overvoltage Protector Series
There are 8/20 short circuit current defined generators. These are usually very high current, 10 kA or more and are used for testing a.c.
protectors, primary protection modules and some Gas Discharge Tubes.
Manufacturers are being increasingly required to design in protection coordination. This means that each protector is operated at its design
level and currents are diverted through the appropriate protector, e.g. the primary level current through the primary protector and lower levels
of current may be diverted through the secondary or inherent equipment protection. Without coordination, primary level currents could pass
through the equipment only designed to pass secondary level currents. To ensure coordination happens with fixed voltage protectors, some
resistance is normally used between the primary and secondary protection (R1a and R1b, Figure 36). The values given in this data sheet apply
to a 400 V (d.c. sparkover) gas discharge tube primary protector and the appropriate test voltage when the equipment is tested with a primary
protector.
If the impulse generator current exceeds the protector’s current rating, then a series resistance can be used to reduce the current to the
protector’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator’s peak voltage by the protector’s rated
current. The impulse generator’s fictive impedance (generator’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance. In some cases, the equipment will require verification over a
temperature range. By using the derated waveform values from the thermal information section, the appropriate series resistor value can be
calculated for ambient temperatures in the range of 0
°
C to 70
°
C.
Figure 34.
C
2
30 nF
R
1
76
C
1
1
μ
F
R
2
13
SW
V
C
1 kV
K.22 1.2/50 GENERATOR
C
3
8 nF
C
4
8 nF
NOTE: SOME STANDARDS
REPLACE OUTPUT
CAPACITORS WITH
25
RESISTORS
Standard
Peak Voltage
Setting
V
Voltage
Waveform
μ
s
2/10
10/1000
10/160
10/560
9/720
(SINGLE)
(DUAL)
0.5/700
10/700
(SINGLE)
(SINGLE)
(DUAL)
Peak Current
Value
A
Current
Waveform
μ
s
2/10
10/1000
10/160
10/560
5/320
5/320
4/250
0.2/310
5/310
5/310
5/310
4/250
TISP7xxxF3
25
°
C Rating
A
Series
Resistance
Coordination
Resistance
(Min.)
GR-1089-CORE
2500
1000
1500
800
1000
1500
1500
1500
1000
1500
4000
4000
2 x 500
2 x 100
200
100
25
37.5
2 x 27
37.5
25
37.5
100
2 x 72
2 x 190
2 x 45
110
50
70
70
2 x 95
70
70
70
70
2 x 95
12
NA
FCC Part 68
(March 1998)
6
8
NA
0
I 31-24
0
0
0
NA
NA
NA
6
6
ITU-T K.20/K.21
17
0
FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
NA = Not Applicable, primary protection removed or not specified.
相關PDF資料 |
PDF描述 |
|---|---|
| TISP7380F3SL-S | MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7150F3SL-S | MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7180F3D | MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7180F3DR | MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP7180F3DR-S | MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TISP7380F3SLS | 制造商:Bourns Inc 功能描述: |
| TISP7380F3SL-S | 功能描述:硅對稱二端開關元件 Triple Element Bidirectional RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP7400H3SL | 功能描述:硅對稱二端開關元件 Triple Element Bidirectional RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP7400H3SL-S | 功能描述:硅對稱二端開關元件 Triple Element Bidirectional RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP7XXXF3 | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:MEDIUM & HIGH-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
發布緊急采購，3分鐘左右您將得到回復。