- 您現在的位置：買賣IC網 > PDF目錄383998 > TISP4395M3BJR (BOURNS INC) BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS PDF資料下載
參數資料
| 型號： | TISP4395M3BJR |
| 廠商： | BOURNS INC |
| 元件分類： | 浪涌電流限制器 |
| 英文描述： | BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| 中文描述： | 395 V, 32 A, SILICON SURGE PROTECTOR, DO-214AA |
| 封裝： | PLASTIC, SMBJ, 2 PIN |
| 文件頁數： | 10/15頁 |
| 文件大小： | 398K |
| 代理商： | TISP4395M3BJR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁
NOVEMBER 1997 - REVISED FEBRUARY 2005
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
TISP4xxxM3BJ Overvoltage Protector Series
These devices are two terminal overvoltage protectors. They may be used either singly to limit the voltage between two conductors (Figure 13)
or in multiples to limit the voltage at several points in a circuit (Figure 14).
APPLICATIONS INFORMATION
Deployment
Impulse Testing
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table below shows some common values.
Figure 13. Two Point Protection
Th1
Figure 14. Multi-Point Protection
Th3
Th2
Th1
In Figure 13, protector Th1 limits the maximum voltage between the two conductors to
±
V(BO). This configuration is normally used to protect
circuits without a ground reference, such as modems. In Figure 14, protectors Th2 and Th3 limit the maximum voltage between each conduc-
tor and ground to the
±
V(BO) of the individual protector. Protector Th1 limits the maximum voltage between the two conductors to its
±
V(BO)
value. If the equipment being protected has all its vulnerable components connected between the conductors and ground, then protector Th1
is not required.
Standard
Peak Voltage
Setting
V
Voltage
Wave Shape
μ
s
2/10
10/1000
10/160
10/560
9/720
9/720
0.5/700
Peak Current
Value
A
Current
Wave Shape
μ
s
2/10
10/1000
10/160
10/560
5/320
5/320
0.2/310
TISP4XXXM3
25
°
C Rating
A
Series
Resistance
GR-1089-CORE
2500
1000
1500
800
1500
1000
1500
1500
4000
500
100
200
100
37.5
25
37.5
37.5
100
300
50
120
75
100
100
100
11
FCC Part 68
(March 1998)
2x5.6
3
0
0
0
I3124
ITU-T K.20/K.21
10/700
5/310
100
0
FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
If the impulse generator current exceeds the protector’s current rating, then a series resistance can be used to reduce the current to the
protector’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator’s peak voltage by the protector’s rated
current. The impulse generator’s fictive impedance (generator’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance.
For the FCC Part 68 10/560 waveform, the following values result. The minimum total circuit impedance is 800/75 = 10.7
and the generator’s
fictive impedance is 800/100 = 8
. This gives a minimum series resistance value of 10.7 - 8 = 2.7
. After allowing for tolerance, a 3
±
10%
resistor would be suitable. The 10/160 waveform needs a standard resistor value of 5.6
per conductor. These would be R1a and R1b in
Figure 16 and Figure 17. FCC Part 68 allows the equipment to be non-operational after the 10/160 (conductor to ground) and 10/560 (inter-
conductor) impulses. The series resistor value may be reduced to zero to pass FCC Part 68 in a non-operational mode, e.g. Figure 15. For this
type of design, the series fuse must open before the TISP4xxxM3 fails. For Figure 15, the maximum fuse i
2
t is 2.3 A
2
s. In some cases, the
equipment will require verification over a temperature range. By using the rated waveform values from Figure 12, the appropriate series resistor
value can be calculated for ambient temperatures in the range of -40
°
C to 85
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TISP4395M3BJR-S | BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4395M3BJ-S | BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4400M3BJR | BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4400M3BJR-S | BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4400M3BJ-S | BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TISP4395M3BJR-S | 功能描述:硅對稱二端開關元件 BI-DIRECTIONL PRTCTR 320volts RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP4395M3BJ-S | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4395M3LM | 功能描述:硅對稱二端開關元件 RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP4395M3LMFR | 功能描述:硅對稱二端開關元件 RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| TISP4395M3LMFRS | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
發布緊急采購，3分鐘左右您將得到回復。